Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the driver door only, but the entry unlock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the front door outside handle assembly (for driver door) (lock sensor) (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [lock sensor]).

WIRING DIAGRAM

B249951E93
1.198,0.313 1.583,0.469 0.385,0.156 10 false ANT1 1.188,0.771 1.583,0.927 0.396,0.156 10 false ANT2 0.24,2.948 0.448,3.104 0.208,0.156 10 false n1 1.24,2.604 1.583,2.75 0.344,0.146 10 false GND 1.667,0.677 1.771,0.833 0.104,0.156 10 false 3 1.677,2.51 1.781,2.667 0.104,0.156 10 false 2 1.667,0.229 1.771,0.375 0.104,0.146 10 false 6 5.656,0.313 6.073,0.479 0.417,0.167 10 false CLG1 5.646,0.771 6.073,0.927 0.427,0.156 10 false CG1B 5.646,2.604 5.823,2.771 0.177,0.167 10 false E 5.448,0.219 5.563,0.375 0.115,0.156 10 false 3 5.448,0.688 5.573,0.854 0.125,0.167 10 false 4 1.448,1.24 1.583,1.396 0.135,0.156 10 false B 1.177,1.688 1.573,1.844 0.396,0.156 10 false SENS 1.667,1.583 1.771,1.74 0.104,0.156 10 false 4 1.667,1.135 1.771,1.281 0.104,0.146 10 false 5 5.656,1.24 6.073,1.406 0.417,0.167 10 false POS1 5.646,1.688 6.073,1.844 0.427,0.156 10 false SEN1 5.365,1.135 5.542,1.292 0.177,0.156 10 false 32 5.365,1.594 5.552,1.76 0.188,0.167 10 false 20 1.188,2.146 1.583,2.302 0.396,0.156 10 false TRG+ 1.667,2.031 1.771,2.188 0.104,0.156 10 false 1 5.646,2.156 6.073,2.313 0.427,0.156 10 false TSW1 5.365,2.063 5.552,2.229 0.188,0.167 10 false 18 5.365,2.521 5.563,2.688 0.198,0.167 10 false 15 5.292,2.927 5.594,3.083 0.302,0.156 10 false L62 5.292,3.094 6.927,3.458 1.635,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.24,3.104 1.958,3.479 1.719,0.375 10 false Front Door Outside Handle Assembly (for Driver Door)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING GTS (LOCK SENSOR)

NG

2.READ VALUE USING GTS (LOCK SENSOR)
a.

Using the GTS, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D-Door Trigger Switch Driver door touch sensor (lock sensor) / ON or OFF ON: Driver door touch sensor (lock sensor) touched
OFF: Driver door touch sensor (lock sensor) not touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.



OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.


b.

Disconnect the L62 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
n1-1 (TRG+) - L62-18 (TSW1) Always Below 1 Ω
L62-15 (E) - Body ground Always Below 1 Ω
n1-1 (TRG+) or L62-18 (TSW1) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
m1-1 (TRG+) - L62-18 (TSW1) Always Below 1 Ω
L62-15 (E) - Body ground Always Below 1 Ω
m1-1 (TRG+) or L62-18 (TSW1) - Body ground Always 10 kΩ or higher




OK

4.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (DRIVER DOOR LOCK SENSOR SIGNAL INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (DRIVER DOOR LOCK SENSOR SIGNAL INPUT)
a.

Connect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.

*1: for LHD

*2: for RHD


U154787E02
0.427,1.01 0.573,1.01 0.573,1.01 0.844,1.417 false 2.573,2.021 2.427,2.021 2.427,2.021 2.302,1.552 false 5.323,0.427 5.969,0.094 5.969,0.094 6.156,0.094 false 5.969,0.094 5.865,0.427 false 0.052,0.01 0.313,0.26 0.26,0.25 10 false *a 4.479,0.042 4.74,0.292 0.26,0.25 10 false *1 6.188,0.031 6.385,0.219 0.198,0.188 10 false *b 4.354,0.958 4.688,1.156 0.333,0.198 10 false GND 0.313,0.927 0.438,1.125 0.125,0.198 10 false E 1.479,0.844 1.781,1.042 0.302,0.198 10 false L62 2.594,1.948 3.021,2.146 0.427,0.198 10 false TSW1

Text in Illustration
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b In actuality, sampling is being performed


b.

Connect the L62 certification ECU (smart key ECU assembly) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
L62-18 (TSW1) - L62-15 (E) Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)