If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (indoor electrical key antenna assembly [front floor], [rear floor] or [inside luggage]) and electrical key transmitter sub-assembly, or the certification ECU (smart key ECU assembly) may be malfunctioning. When the electrical key transmitter sub-assembly is brought into the vehicle, verification of the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) is performed. If verification cannot be performed or the codes do not match, the power switch cannot be turned on (IG) and the hybrid control system cannot be started.
When a door is unlocked and the electrical key transmitter sub-assembly is brought into the vehicle, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna assembly which transmits electric waves to detect the electrical key transmitter sub-assembly. If the electrical key transmitter sub-assembly recognizes that it is in the detection area, it responds with the key ID code. This information is received by the indoor electrical key antenna and then sent to the certification ECU (smart key ECU assembly).
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the power switch off to troubleshoot:
Connect the GTS to the vehicle and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".
Indoor electrical key antenna assembly have an antenna coil between each two CLG terminals.
Check that the entry lock and unlock functions operate for each door (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
OK
NG
Remove the transmitter battery of the electrical key transmitter (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).
With the brake pedal depressed, touch the TOYOTA mark of the electrical key transmitter sub-assembly to the power switch.
When operating the power switch, check whether the hybrid control system starts.
When the electrical key transmitter sub-assembly cannot be verified even though it is inside the detection area, the hybrid control system start check can be performed by removing the transmitter battery from the electrical key transmitter sub-assembly and holding the electrical key transmitter sub-assembly against the power switch.
If the hybrid control system cannot be started when performing this inspection, the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) may be malfunctioning.
Hybrid control system starts.
| *1 | Power Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
OK
NG
Install the transmitter battery to the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a entry and start system check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
As the effect of electric wave interference decreases by moving the electrical key transmitter sub-assembly close to the door control receiver, it may be possible to check whether electric wave interference is the cause of the problem.
| Result | Proceed to |
|---|---|
| System cannot be operated | A |
| System can be operated | B |
If the problem only occurs in specific places or at specific times, electric wave interference may be the cause of the problem . Also, the vehicle may be have the effects of electric wave interference with the parts installed by the dealer. As a result, when parts have been installed by the dealer, it may be necessary to remove those parts before inspecting the vehicle.
There may be electric wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the key detection area) and RF band (used by the key for transmission) to check for locations where there is electric wave interference.
A
B
Check the following antennas in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).
Check the No. 1 indoor electrical key antenna assembly (front floor).
| *a | Inspection Point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Check the No. 3 indoor electrical key antenna assembly (rear floor).
| *a | Inspection Point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Check the No. 2 indoor electrical key antenna assembly (inside luggage).
| *a | Inspection Point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.
It is possible to check which indoor electrical key antenna assembly (front floor, rear floor or inside luggage) is operating by the sounding of the buzzer.
If the buzzer does not sound for any indoor electrical key antenna assemblies, the certification ECU (smart key ECU assembly) circuit may have a malfunction.
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| Front operation check fails | A |
| Rear operation check fails | B |
| Luggage operation check fails | C |
| Front, rear and luggage operation checks are normal | D |
A
B
C
D
Disconnect the L11 No. 1 indoor electrical key antenna assembly (front floor) connector.
Disconnect the L62 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L11-1 (ANTE5) - L62-7 (CLG5) | Always | Below 1 Ω |
| L11-3 (CLGB) - L62-8 (CG5B) | Always | Below 1 Ω |
| L11-1 (ANTE5) or L62-7 (CLG5) - Body ground | Always | 10 kΩ or higher |
| L11-3 (CLGB) or L62-8 (CG5B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the L11 No. 1 indoor electrical key antenna assembly (front floor) connector.
Connect the L62 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| L11-1 (ANTE5) - L11-3 (CLGB) | Procedure:
1.
Power switch off 2.
Key not inside vehicle 3.
Door is open 4.
Door is closed 5.
30 seconds elapse |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
| *1 | Waveform |
| *a | Front view of wire harness connector
(to No. 1 indoor Electrical Key Antenna Assembly [Front Floor]) |
| *b | Door open |
| *c | After approximately 30 seconds from when the door is closed |
OK
NG
Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Floor)>REMOVAL).
NEXT
Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).
Check the No. 1 indoor electrical key antenna assembly (front floor).
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| *a | Inspection Point |
OK
NG
Disconnect the R10 No. 3 indoor electrical key antenna assembly (rear floor) connector.
Disconnect the L62 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R10-1 (ANTE6) - L62-24 (CLG6) | Always | Below 1 Ω |
| R10-3 (CLGB) - L62-25 (CG6B) | Always | Below 1 Ω |
| R10-1 (ANTE6) or L62-24 (CLG6) - Body ground | Always | 10 kΩ or higher |
| R10-3 (CLGB) or L62-25 (CG6B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the R10 No. 3 indoor electrical key antenna assembly (rear floor) connector.
Connect the L62 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| R10-1 (ANTE6) - R10-3 (CLGB) | Procedure:
1.
Power switch off 2.
Key not inside vehicle 3.
Door is open 4.
Door is closed 5.
30 seconds elapse |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
| *1 | Waveform |
| *a | Front view of wire harness connector
(to No. 3 indoor Electrical Key Antenna Assembly [Rear Floor]) |
| *b | Door open |
| *c | After approximately 30 seconds from when the door is closed |
OK
NG
Temporarily replace the No. 3 indoor electrical key antenna assembly (rear floor) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Center Floor)>REMOVAL).
NEXT
Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).
Check the No. 3 indoor electrical key antenna assembly (rear floor).
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| *a | Inspection Point |
OK
NG
Disconnect the S26 No. 2 indoor electrical key antenna assembly (inside luggage) connector.
Disconnect the L62 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S26-1 (ANTE7) - L62-26 (CLG7) | Always | Below 1 Ω |
| S26-3 (CLGB) - L62-27 (CG7B) | Always | Below 1 Ω |
| S26-1 (ANTE7) or L62-26 (CLG7) - Body ground | Always | 10 kΩ or higher |
| S26-3 (CLGB) or L62-27 (CG7B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the S26 No. 2 indoor electrical key antenna assembly (inside luggage) connector.
Connect the L62 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| S26-1 (ANTE7) - S26-3 (CLGB) | Procedure:
1.
Power switch off 2.
Key not inside vehicle 3.
Door is open 4.
Door is closed 5.
30 seconds elapse |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
| *1 | Waveform |
| *a | Front view of wire harness connector
(to No. 2 indoor Electrical Key Antenna Assembly [Inside Luggage]) |
| *b | Door open |
| *c | After approximately 30 seconds from when the door is closed |
OK
NG
Temporarily replace the No. 2 indoor electrical key antenna assembly (inside luggage) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL).
NEXT
Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).
Check the No. 2 indoor electrical key antenna assembly (inside luggage).
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| *a | Inspection Point |
OK
NG