Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the back door only, but the entry unlock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the lock switch (connection between the back door opener switch assembly and certification ECU (smart key ECU assembly)).

WIRING DIAGRAM

B265877E21
5.385,0.719 5.802,0.896 0.417,0.177 10 false TSW5 5.135,0.625 5.313,0.802 0.177,0.177 10 false 22 5.396,1.208 5.813,1.385 0.417,0.177 10 false TSW6 5.135,1.125 5.313,1.302 0.177,0.177 10 false 23 5.156,1.604 5.438,1.781 0.281,0.177 10 false L62 5.156,1.76 6.719,2.125 1.563,0.365 10 false Certification ECU (Smart Key ECU Assembly) 1.333,1.667 1.698,1.844 0.365,0.177 10 false V4 1.333,1.823 2.625,2.26 1.292,0.438 10 false Back Door Opener Switch Assembly 2.49,0.604 2.698,0.781 0.208,0.177 10 false UL 1.688,1.365 2.448,1.542 0.76,0.177 10 false Lock Switch 1.625,0.854 2.51,1.031 0.885,0.177 10 false Unlock Switch 2.781,0.604 2.958,0.781 0.177,0.177 10 false 3 2.573,1.104 2.688,1.281 0.115,0.177 10 false L 1.406,1.125 1.521,1.302 0.115,0.177 10 false E 2.781,1.104 2.958,1.281 0.177,0.177 10 false 1 1.188,1.125 1.365,1.302 0.177,0.177 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING GTS (LOCK SWITCH)

NG

2.READ VALUE USING GTS (LOCK SWITCH)
a.

Using the GTS, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Tr/B-Door Lock SW Back door opener switch (lock switch) / ON or OFF ON: Back door opener switch (lock switch) pushed
OFF: Back door opener switch (lock switch) not pushed
·

Displays whether the back door opener switch assembly (lock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.



OK:

The GTS display changes correctly in response to the operation of the back door opener switch assembly.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU)
3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU)
a.

Disconnect the V4 back door opener switch assembly connector.


b.

Disconnect the L62 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-1 (L) - L62-23 (TSW6) Always Below 1 Ω
V4-2 (E) - Body ground Always Below 1 Ω
V4-1 (L) or L62-23 (TSW6) - Body ground Always 10 kΩ or higher




OK

4.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (LOCK SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (LOCK SWITCH)
a.

Remove the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL).


B142645E11
1.948,1.399 2.427,1.843 false 1.231,1.848 1.71,1.404 false 2.433,1.865 2.590,2.015 0.157,0.150 10 L 0.18,0.164 0.338,0.315 0.157,0.151 10 *a 1.118,1.865 1.232,2.015 0.114,0.150 10 E

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (L) - 2 (E) No switch pushed 10 kΩ or higher
1 (L) - 2 (E) Lock switch pushed Below 1 Ω


Text in Illustration
*a Component without harness connected
(Back Door Opener Switch Assembly)



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY