The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for driver door) [electrical key antenna] at intervals of 250 ms. For the front door outside handle assembly (for driver door) [electrical key antenna] to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 250 ms. DTC B27A1 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [electrical key antenna] (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B27A1 | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*). | ·
Harness or connector ·
Front door outside handle assembly (for driver door) ·
Certification ECU (smart key ECU assembly) |
Any time |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Entry lock/unlock operation cannot be performed for driver door | - |
| DTC Code | Data List and Active Test |
|---|---|
| B27A1 | Key diagnostic mode can be used to perform troubleshooting |
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the power switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".
Front door outside handle assembly (for driver door) has an antenna coil between ANT1 and ANT2 terminals.
Turn the power switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door).
Connectors are properly connected.
OK
NG
Disconnect the L62 certification ECU (smart key ECU assembly) connector.
Disconnect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.
Measure the resistance according to the value(s) in the table below.
*1: for LHD
*2: for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L62-3 (CLG1) - n1-6 (ANT1) | Always | Below 1 Ω |
| L62-4 (CG1B) - n1-3 (ANT2) | Always | Below 1 Ω |
| L62-15 (E) - Body ground | Always | Below 1 Ω |
| n1-2 (GND) - Body ground | Always | Below 1 Ω |
| L62-3 (CLG1) or n1-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| L62-4 (CG1B) or n1-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L62-3 (CLG1) - m1-6 (ANT1) | Always | Below 1 Ω |
| L62-4 (CG1B) - m1-3 (ANT2) | Always | Below 1 Ω |
| L62-15 (E) - Body ground | Always | Below 1 Ω |
| m1-2 (GND) - Body ground | Always | Below 1 Ω |
| L62-3 (CLG1) or m1-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| L62-4 (CG1B) or m1-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the L62 certification ECU (smart key ECU assembly) connector.
| *1 | Waveform 1 | *2 | Waveform 2 |
| *a | Component with harness connected
(Certification ECU (smart key ECU assembly)) |
- | - |
Connect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.
Using an oscilloscope, check the waveform.
*1: for LHD
*2: for RHD
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| L62-3 (CLG1) - L62-15 (E) | Procedure:
1.
Power switch off 2.
Key brought outside vehicle 3.
All doors closed 4.
Key not inside vehicle 5.
Key brought inside detection area*3 6.
All doors locked through wireless operation |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 1) |
| L62-3 (CLG1) - L62-15 (E) | Procedure:
1.
Power switch off 2.
Key brought outside vehicle 3.
All doors closed 4.
Key not inside vehicle 5.
Key brought outside detection area*4 6.
All doors locked through wireless operation |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 2) |
| L62-4 (CG1B) - L62-15 (E) | Procedure:
1.
Power switch off 2.
Key brought outside vehicle 3.
All doors closed 4.
Key not inside vehicle 5.
Key brought outside detection area*4 6.
All doors locked with key |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 2) |
*3: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
*4: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
OK
NG
Temporarily replace the front door outside handle assembly (for driver door) with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).
NEXT
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).
DTC B27A1 is not output.
OK
NG