Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A5  Open in Front Floor Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 1 indoor electrical key antenna assembly (front floor). For the No. 1 indoor electrical key antenna assembly (front floor) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A5 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (between terminals CLG5 and ANTE5, or terminals CG5B and CLGB).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A5 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (CLG5 - ANTE5, CG5B - CLGB) (1 trip detection logic*).
·

Harness or connector

·

No. 1 indoor electrical key antenna assembly (front floor)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in front seat area:
·

Power source mode does not change when power switch is pressed

·

Key locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A5 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B249967E56
1.105,0.406 1.570,0.567 0.465,0.160 10 ANTE5 1.172,0.878 1.571,1.038 0.399,0.160 10 CLGB 0.071,1.347 0.348,1.508 0.278,0.160 10 L11 1.669,0.765 1.774,0.924 0.105,0.158 10 3 1.671,0.314 1.776,0.460 0.105,0.145 10 1 5.652,0.406 6.069,0.573 0.416,0.167 10 CLG5 5.644,0.878 6.074,1.034 0.430,0.156 10 CG5B 5.648,1.329 5.826,1.493 0.178,0.164 10 E 5.443,0.309 5.559,0.466 0.116,0.157 10 7 5.443,0.783 5.568,0.949 0.124,0.166 10 8 5.365,1.241 5.560,1.402 0.195,0.162 10 15 5.317,1.701 5.615,1.856 0.298,0.155 10 L62 5.317,1.854 6.871,2.209 1.553,0.355 10 Certification ECU (Smart Key ECU Assembly) 0.072,1.493 2.082,1.869 2.010,0.375 10 No. 1 indoor Electrical Key Antenna Assembly (Front Floor)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".

·

No. 1 indoor electrical key antenna assembly (front floor) has an antenna coil between ANTE5 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INDOOR ELECTRICAL KEY ANTENNA)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INDOOR ELECTRICAL KEY ANTENNA)
a.

Disconnect the L62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L11 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L62-7 (CLG5) - L11-1 (ANTE5) Always Below 1 Ω
L62-8 (CG5B) - L11-3 (CLGB) Always Below 1 Ω
L62-15 (E) - Body ground Always Below 1 Ω
L62-7 (CLG5) or L11-1 (ANTE5) - Body ground Always 10 kΩ or higher
L62-8 (CG5B) or L11-3 (CLGB) - Body ground Always 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA [FRONT FLOOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA [FRONT FLOOR])
a.

Connect the L62 certification ECU (smart key ECU assembly) connector.

U154571E03
0.406,1.021 0.552,1.021 0.552,1.021 0.823,1.427 false 2.396,0.917 2.25,0.917 2.25,0.917 1.969,1.427 false 2.125,0.698 1.979,0.698 1.979,0.698 1.885,1.417 false 0.052,0 0.313,0.25 0.26,0.25 10 false *a 4.479,0.031 4.74,0.281 0.26,0.25 10 false *1 4.958,1.552 5.146,1.76 0.188,0.208 10 false *b 5.698,1.542 5.885,1.75 0.188,0.208 10 false *c 4.354,0.802 4.688,1 0.333,0.198 10 false GND 0.292,0.938 0.417,1.135 0.125,0.198 10 false E 2.156,0.635 2.552,0.833 0.396,0.198 10 false CG5B 1.479,0.844 1.781,1.042 0.302,0.198 10 false L62 2.427,0.854 2.823,1.052 0.396,0.198 10 false CLG5

Text in Illustration
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Door open
*c After approximately 30 seconds from when the door is closed - -


b.

Connect the L11 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
L62-7 (CLG5) - L62-15 (E) Procedure:
1.

Power switch off

2.

Key not inside vehicle

3.

Door is open

4.

Door is closed

5.

30 seconds elapse


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)
L62-8 (CG5B) - L62-15 (E) Procedure:
1.

Power switch off

2.

Key not inside vehicle

3.

Door is open

4.

Door is closed

5.

30 seconds elapse


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)




OK

4.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Floor)>REMOVAL).



NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)