The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 2 indoor electrical key antenna assembly (inside luggage). For the No. 2 indoor electrical key antenna assembly (inside luggage) to detect when the electrical key transmitter sub-assembly is inside the luggage compartment, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the luggage compartment. DTC B27A7 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (inside luggage) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B27A7 | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (inside luggage) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*). | ·
Harness or connector ·
No. 2 indoor electrical key antenna assembly (inside luggage) ·
Certification ECU (smart key ECU assembly) |
Any time |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| When electrical key transmitter sub-assembly is in luggage compartment:
·
Power source mode does not change when power switch is pressed ·
Electrical key transmitter sub-assembly becomes locked inside vehicle |
- |
| DTC Code | Data List and Active Test |
|---|---|
| B27A7 | Key diagnostic mode can be used to perform troubleshooting |
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the power switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
No. 2 indoor electrical key antenna assembly (inside luggage) has an antenna coil between ANTE7 and CLGB terminals.
Turn the power switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (inside luggage).
Connectors are properly connected.
OK
NG
Disconnect the L62 certification ECU (smart key ECU assembly) connector.
Disconnect the S26 No. 2 indoor electrical key antenna assembly (inside luggage) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L62-26 (CLG7) - S26-1 (ANTE7) | Always | Below 1 Ω |
| L62-27 (CG7B) - S26-3 (CLGB) | Always | Below 1 Ω |
| L62-15 (E) - Body ground | Always | Below 1 Ω |
| L62-26 (CLG7) or S26-1 (ANTE7) - Body ground | Always | 10 kΩ or higher |
| L62-27 (CG7B) or S26-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the L62 certification ECU (smart key ECU assembly) connector.
| *1 | Waveform | - | - |
| *a | Component with harness connected
(Certification ECU (smart key ECU assembly)) |
*b | Door open |
| *c | After approximately 30 seconds from when the door is closed | - | - |
Connect the S26 No. 2 indoor electrical key antenna assembly (inside luggage) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| L62-26 (CLG7) - L62-15 (E) | Procedure:
1.
Power switch off 2.
Key not inside vehicle 3.
Door is open 4.
Door is closed 5.
30 seconds elapse |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
| L62-27 (CG7B) - L62-15 (E) | Procedure:
1.
Power switch off 2.
Key not inside vehicle 3.
Door is open 4.
Door is closed 5.
30 seconds elapse |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
OK
NG
Temporarily replace the No. 2 indoor electrical key antenna assembly (inside luggage) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL).
NEXT
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).
DTC B27A7 is not output.
OK
NG