Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG1 drive circuit, IG2 drive circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2271 When either of the following conditions is met (1-trip detection logic*):
·

The IG1 or IG2 circuit in the certification ECU (smart key ECU assembly) is malfunctioning.

·

The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.


·

ECU-B2 fuse

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Turn the power switch on (IG).
HINT:

To turn the power switch on (IG), carry the key and press the power switch twice with park (P) selected and the brake pedal released.



*: Only output while a malfunction is present and the power switch is on (IG)


HINT:
·

The IG1 and IG2 drive circuits activate the IG1 and IG2 relays.

·

After the IG1 and IG2 drive circuits turn on, even if the certification ECU (smart key ECU assembly) operates incorrectly, the IG hold circuit maintains the power switch on (IG) state.



Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The power source mode is not allowed to change to on (IG) (the hybrid control system cannot be started). The power source mode cannot be changed to on (IG).

WIRING DIAGRAM

B452138E03
1.885,7.052 3.5,7.49 1.615,0.438 10 false Certification ECU (Smart Key ECU Assembly) 4.167,6.104 4.427,6.24 0.26,0.135 10 false 1A 3.021,1.167 3.406,1.417 0.385,0.25 10 false L195 3.156,0.99 3.25,1.188 0.094,0.198 10 false 6 4.688,1.479 5.333,1.688 0.646,0.208 10 false IG1 NO. 1 4.688,2.667 5.344,2.854 0.656,0.188 10 false IG1 NO. 2 4.667,3.833 5.313,3.969 0.646,0.135 10 false IG1 NO. 3 3.656,4.521 6.406,4.771 2.75,0.25 10 false Instrument Panel Junction Block Assembly 4.708,6.792 6.344,7.063 1.635,0.271 10 false Integration Relay 4.875,6.406 5.125,6.552 0.25,0.146 10 false IG2 1.813,6.531 2.198,6.677 0.385,0.146 10 false L195 4.229,5.948 4.5,6.083 0.271,0.135 10 false 2 5.906,6.104 6.167,6.24 0.26,0.135 10 false 1A 5.958,5.938 6.229,6.104 0.271,0.167 10 false 3 1.896,6.354 2.104,6.49 0.208,0.135 10 false 11 2.198,6.531 2.469,6.667 0.271,0.135 10 false E 1.938,0.427 2.125,0.615 0.188,0.188 10 false 2 2.198,0.583 2.479,0.781 0.281,0.198 10 false +B 2.615,1.156 2.969,1.313 0.354,0.156 10 false IG1D 3.594,0.563 3.875,0.719 0.281,0.156 10 false 2E 3.604,1 3.802,1.281 0.198,0.281 10 false 25 3.594,1.167 3.865,1.365 0.271,0.198 10 false 2B 1.031,0.74 1.688,1.042 0.656,0.302 10 false ECU-B2 0.042,0.51 0.896,0.844 0.854,0.333 10 false from Auxiliary Battery 3.021,6.104 3.479,6.313 0.458,0.208 10 false L195 3.135,5.917 3.354,6.094 0.219,0.177 10 false 9 2.625,6.083 3.115,6.292 0.49,0.208 10 false IG2D 5.625,0.906 6.177,1.24 0.552,0.333 10 false ECU-IG NO. 1 5.635,3.302 6.354,3.635 0.719,0.333 10 false ECU-ACC 5.76,2.073 6.313,2.406 0.552,0.333 10 false WIP 6.208,0.76 6.469,1.042 0.26,0.281 10 false 2A 6.208,0.583 6.479,0.823 0.271,0.24 10 false 19 6.208,1.938 6.458,2.188 0.25,0.25 10 false 2A 6.208,1.76 6.469,1.896 0.26,0.135 10 false 11 6.219,2.948 6.417,3.229 0.198,0.281 10 false 34 6.208,3.125 6.479,3.313 0.271,0.188 10 false 2B 6.24,3.854 6.438,4.135 0.198,0.281 10 false 6 6.208,4.042 6.469,4.229 0.26,0.188 10 false 2B 3.615,0.75 3.885,0.99 0.271,0.24 10 false 2F 3.646,0.396 3.75,0.531 0.104,0.135 10 false 1 3.854,0.563 4.125,0.802 0.271,0.24 10 false *1 3.844,0.854 4.115,1.094 0.271,0.24 10 false *2 0.302,5.667 2.146,5.906 1.844,0.24 10 false *1: for LHD 0.292,6.063 1.188,6.302 0.896,0.24 10 false *2: for RHD 1.813,0.615 2.198,0.865 0.385,0.25 10 false L195

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2271
Power Source Control
·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

Latch Circuit


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Disconnect the L195 certification ECU (smart key ECU assembly) connector.


b.
U190841E02
1.292,1.354 1.083,1.896 true 0.094,0.052 0.281,0.208 0.188,0.156 10 false *a 0.302,1.365 0.688,1.521 0.385,0.156 10 false L195 0.948,1.917 1.146,2.063 0.198,0.146 10 false +B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L195-2 (+B) - Body ground Power switch off 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
U190842E02
2.063,1.344 2.198,1.885 true 0.094,0.052 0.281,0.208 0.188,0.156 10 false *a 0.302,1.365 0.688,1.521 0.385,0.156 10 false L195 2.167,1.917 2.365,2.063 0.198,0.146 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L195-11 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the L195 and L197 certification ECU (smart key ECU assembly) connectors.

U190837E02
4.385,1.625 4.125,2.292 true 1.979,1.74 1.76,2.292 true 0.302,0.292 0.49,0.448 0.188,0.156 10 false *a 4.781,0.938 5.24,1.094 0.458,0.156 10 false L197 2.156,0.927 2.646,1.083 0.49,0.156 10 false L195 3.927,2.313 4.292,2.469 0.365,0.156 10 false IG1D 1.531,2.313 1.896,2.469 0.365,0.156 10 false IG2D


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L195-9 (IG2D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher
L197-6 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher


Text in Illustration
*a Component with harness connected
(to Certification ECU (Smart Key ECU Assembly))
- -



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)