Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2015.08–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when there is a problem in the ACC output circuit. The ACC circuit is the circuit that goes from inside the power management control ECU to the ACC relay.

HINT:
·

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



This DTC is stored when a malfunction in the ACC output circuit between the ACC output terminal of the power management control ECU and the ACC relay is detected.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2274 Malfunction in the ACC relay activation circuit in the power management control ECU or the external circuit (1-trip detection logic*).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

AM2 fuse

·

ACC relay (Instrument panel junction block assembly)

·

Power management control ECU

·

Wire harness or connector


Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.
HINT:

To turn the power switch on (ACC), carry the key and press the power switch with park (P) selected and the brake pedal released.



*: Only output while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction when the relay is stuck on, the ACC relay does not turn off even though all the power is off.

·

If there is a malfunction when the relay is off, the ACC relay does not turn on even though the power source mode is on (ACC).


HINT:

The power source can change to on (IG) and the hybrid control system can be started.


-

WIRING DIAGRAM

B231374E07
0.299,0.339 1.177,0.644 0.878,0.304 10 from Auxiliary Battery 1.51,0.538 1.813,0.675 0.303,0.137 10 AM2 2.601,0.411 2.858,0.549 0.257,0.137 10 L6 2.601,0.805 2.849,0.942 0.248,0.137 10 L5 2.886,0.411 3.275,0.549 0.389,0.137 10 AM21 2.886,0.805 3.268,0.942 0.382,0.137 10 AM22 3.389,0.805 3.800,0.942 0.412,0.137 10 ACCD 2.601,1.202 2.849,1.339 0.248,0.137 10 L5 2.635,1.025 2.732,1.162 0.097,0.137 10 5 2.635,1.426 2.732,1.563 0.097,0.137 10 5 2.635,1.818 2.732,1.955 0.097,0.137 10 6 2.635,2.223 2.732,2.360 0.097,0.137 10 4 2.886,1.202 3.153,1.339 0.267,0.137 10 E01 2.601,1.603 2.849,1.740 0.248,0.137 10 L6 2.601,2.398 2.849,2.535 0.248,0.137 10 L6 2.886,1.603 3.155,1.740 0.269,0.137 10 E02 2.601,1.997 2.849,2.134 0.248,0.137 10 L5 2.886,1.997 3.075,2.134 0.189,0.137 10 E1 2.886,2.398 3.157,2.535 0.271,0.137 10 E12 2.663,2.719 3.939,3.034 1.276,0.315 10 Power Management Control ECU 4.736,2.516 6.373,2.831 1.637,0.315 10 Instrument Panel Junction Block Assembly 2.635,0.223 2.732,0.360 0.097,0.137 10 7 2.636,0.617 2.731,0.755 0.094,0.137 10 1 3.924,0.805 4.172,0.942 0.248,0.137 10 L6 3.954,0.625 4.050,0.762 0.095,0.137 10 1 4.507,0.805 4.696,0.942 0.189,0.137 10 2A 5.4,1.063 5.789,1.200 0.389,0.137 10 ACC 5.273,2.086 5.892,2.223 0.619,0.137 10 P/POINT 4.515,0.612 4.688,0.749 0.173,0.137 10 43 6.463,1.839 6.655,1.976 0.191,0.137 10 2B 6.497,1.656 6.594,1.793 0.096,0.137 10 4 6.463,0.816 6.655,0.953 0.191,0.137 10 2B 6.497,0.612 6.594,0.749 0.096,0.137 10 6

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body Electrical / Power Source Control / Trouble Codes.

for Entry&Start: Body Electrical / Entry&Start / Trouble Codes.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the power source mode cannot change to on (ACC), the audio and navigation systems do not operate.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2274
Power Source Control

ACC Relay Monitor


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)

OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
U154553E02
1.615,1.563 1.042,1.771 false 1.604,1.76 1.031,1.969 false 1.76,2.667 2.344,2.906 false 2.24,1.073 2.448,1.24 0.208,0.167 10 false 2B 2.24,2.167 2.448,2.333 0.208,0.167 10 false 2A 2.427,2.875 2.885,3.042 0.458,0.167 10 false 2A-43 0.729,1.708 1.104,1.875 0.375,0.167 10 false 2B-4 0.156,0.125 0.365,0.292 0.208,0.167 10 false *a 0.719,1.917 1.094,2.083 0.375,0.167 10 false 2B-6

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-43 - 2B-4 20°C (68°F) 81.49 to 118.98 Ω
2A-43 - 2B-6 20°C (68°F) 81.49 to 118.98 Ω
2B-4 - 2B-6 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-1 (ACCD) - 2A-43 Always Below 1 Ω
L6-1 (ACCD) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2B-4 - Body ground Always Below 1 Ω
2B-6 - Body ground Always Below 1 Ω




OK

6.INSPECT POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER MANAGEMENT CONTROL ECU
a.
U154550E01
0.057,0.047 0.210,0.183 0.153,0.136 10 *a 2.586,0.456 2.846,0.595 0.260,0.139 10 L6 2.528,1.893 2.939,2.032 0.411,0.139 10 ACCD 2.733,1.902 2.848,1.133 false

Reinstall the instrument panel junction block assembly.


b.

Reconnect the L5 and L6 connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L6-1 (ACCD) - Body ground Power switch on (ACC) 9 V or higher


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)



OK

NG