Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK POWER SWITCH


U190847E02
3.427,0.333 3.771,0.5 0.344,0.167 10 false L194

a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L194-6 (AGND) - Body ground - L - Body ground Transponder key amplifier ground Always Below 1 Ω -
L194-7 (TXCT) - L194-6 (AGND) Input V - B*1
V - B*2
Immobiliser communication input Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
L194-8 (CODE) - L194-6 (AGND) Output L - P Immobiliser communication output Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
L194-10 (VC5) - L194-6 (AGND) Input Y - P Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L194-7 (TXCT) - L194-6 (AGND) Input V - B*1
V - B*2
Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Power switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



L194-8 (CODE) - L194-6 (AGND) Output L - P Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Power switch off, power switch pressed with key held near power switch*3 Pulse generation
(See waveform 2)
L194-10 (VC5) - L194-6 (AGND) Input Y - P Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Power switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 3)

If the result is not as specified, the power switch may have a malfunction.

*1: for LHD

*2: for RHD


HINT:

*3: Remove the key battery before performing this inspection.



c.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052E41
2.802,0.771 3.156,0.958 0.354,0.188 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection L194-7 (TXCT) - L194-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed


ii.
B251418E13
1.833,0.802 2.625,1.542 2.625,1.542 2.74,1.542 false 2.76,0.99 3.198,1.156 0.438,0.167 10 false GND 2.781,1.448 2.958,1.615 0.177,0.167 10 false *a

Waveform 2 (Reference)

Text in Illustration
*a Key held against power switch

Measurement Condition
Item Content
Tester Connection L194-8 (CODE) - L194-6 (AGND)
Tool Setting 1 V/DIV., 200 ms./DIV.
Condition Power switch off, power switch pressed with key held near power switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection L194-10 (VC5) - L194-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U190982E02
1.865,0.583 2.313,0.76 0.448,0.177 10 false L195 3.25,0.573 3.698,0.75 0.448,0.177 10 false L196 4.813,0.583 5.26,0.76 0.448,0.177 10 false L197

a.

Disconnect the L195 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L195-2 (+B) - L195-11 (E) Input B - W-B +B power supply Always 11 to 14 V -
L195-10 (CUTB) - L195-11 (E) Input R - W-B Dark current cut pin Always 11 to 14 V -
L195-11 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the L195 certification ECU (smart key ECU assembly) connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L197-5 (IG) - L195-11 (E) Input V - W-B Ignition power supply Power switch off → on (IG) Below 1 V → 11 to 14 V Ignition Switch
L197-18 (IND) - L195-11 (E) Output GR - W-B Security indicator output Power switch off → on (IG) Pulse generation
→ Below 2 V
-
L197-9 (TXCT) - L197-24 (AGND) Output V - B*1
V - B*2
Signal output to transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


L197-7 (CODE) - L197-24 (AGND) Input L - P Signal input from transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
L197-1 (VC5) - L197-24 (AGND) Output Y - P Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
L197-24 (AGND) - Body ground - P - Body ground Transponder key amplifier ground Always Below 1 Ω


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L197-9 (TXCT) - L197-24 (AGND) Output V - B*1
V - B*2
Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Power switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


L197-7 (CODE) - L197-24 (AGND) Input L - P Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Power switch off, power switch pressed with key held near power switch*3 Pulse generation
(See waveform 2)
L197-1 (VC5) - L197-24 (AGND) Output Y - P Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Power switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 3)

If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.

*1: for LHD

*2: for RHD


HINT:

*3: Remove the key battery before performing this inspection.



f.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052E41
2.802,0.771 3.156,0.958 0.354,0.188 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection L197-9 (TXCT) - L197-24 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed


ii.
B251418E13
1.833,0.802 2.625,1.542 2.625,1.542 2.74,1.542 false 2.76,0.99 3.198,1.156 0.438,0.167 10 false GND 2.781,1.448 2.958,1.615 0.177,0.167 10 false *a

Waveform 2 (Reference)

Text in Illustration
*a Key held against power switch

Measurement Condition
Item Content
Tester Connection L197-7 (CODE) - L197-24 (AGND)
Tool Setting 1 V/DIV., 200 ms./DIV.
Condition Power switch off, power switch pressed with key held near power switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection L197-1 (VC5) - L197-24 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed




CHECK ID CODE BOX (IMMOBILISER CODE ECU)


U190887E02
3.417,0.24 3.76,0.396 0.344,0.156 10 false L191

a.

Disconnect the L191 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L191-1 (+B) - L191-5 (GND) Input W - W-B +B power supply Power switch off 11 to 14 V B2789
L191-5 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω B2789

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the L191 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check the pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L191-3 (EFII) - L191-5 (GND) Input SB - W-B EFI communication input
(Signal input from hybrid vehicle control ECU to ID code box (immobiliser code ECU))
Power switch off 11 to 14 V
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


L191-3 (EFII) - L191-5 (GND) Input SB - W-B EFI communication input
(Signal input from hybrid vehicle control ECU to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 1)
L191-4 (EFIO) - L191-5 (GND) Output LG - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU)
Power switch off Below 1 V
L191-4 (EFIO) - L191-5 (GND) Output LG - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU)
Within 3 seconds of engine start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 2)

If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.



e.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B449160E01
0.74,1.25 1.198,1.448 0.458,0.198 10 false GND 2.708,1.333 3.167,1.531 0.458,0.198 10 false *a 2.896,1.344 3.354,1.542 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection L191-3 (EFII) - L191-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B449161E01
0.75,1.25 1.208,1.448 0.458,0.198 10 false GND 3.115,1.344 3.573,1.542 0.458,0.198 10 false *a 3.302,1.354 3.76,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection L191-4 (EFIO) - L191-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected




CHECK TRANSMISSION CONTROL ECU ASSEMBLY


U154548E02
2.792,0.271 3.104,0.417 0.313,0.146 10 false A23 4.031,0.26 4.302,0.406 0.271,0.146 10 false A24

a.

Disconnect the A23 and A24 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A24-1 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A24-5 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A24-6 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A23-16 (+B) - Body ground Input L - Body ground +B power supply Power switch off 11 to 14 V -
A23-15 (BATT) - Body ground Input SB - Body ground +B power supply Power switch off 11 to 14 V -

If the result is not as specified, there may be a malfunction in the wire harness.



CHECK HYBRID VEHICLE CONTROL ECU


U190815E02
1.479,0.198 1.771,0.365 0.292,0.167 10 false A21 2.792,0.219 3.083,0.385 0.292,0.167 10 false A22 4.323,0.229 4.604,0.396 0.281,0.167 10 false L5 5.583,0.24 5.865,0.406 0.281,0.167 10 false L6

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A21-1 (+B2) - L5-6 (E1) Input L - W-B IG power supply Power switch on (IG) 11 to 14 V -
A22-4 (+B1) - L5-6 (E1) Input L - W-B IG power supply Power switch on (IG) 11 to 14 V -
A22-6 (MREL) - L5-6 (E1) Input BE - W-B IG power supply Power switch on (IG) 11 to 14 V -
L5-5 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
L5-6 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
L6-5 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
L6-23 (IMO) - L5-6 (E1) Input SB - W-B ID code box (immobiliser code ECU) communication input Power switch off 11 to 14 V -
L6-23 (IMO) - L5-6 (E1) Input SB - W-B ID code box (immobiliser code ECU) communication input Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
L6-22 (IMI) - L5-6 (E1) Output LG - W-B ID code box (immobiliser code ECU) communication output Power switch off Below 1 V -
L6-22 (IMI) - L5-6 (E1) Output LG - W-B ID code box (immobiliser code ECU) communication output Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

a.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B449160E05
0.74,1.25 1.198,1.448 0.458,0.198 10 false GND 2.708,1.333 3.167,1.531 0.458,0.198 10 false *a 2.896,1.344 3.354,1.542 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection L6-23 (IMO) - L5-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B449161E01
0.75,1.25 1.208,1.448 0.458,0.198 10 false GND 3.115,1.344 3.573,1.542 0.458,0.198 10 false *a 3.302,1.354 3.76,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection L6-22 (IMI) - L5-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected