Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

When there are communication malfunctions between the power management control ECU and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the power management control ECU stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2799 Either condition is met (1 trip detection logic*):
·

A malfunction in the communication or communication lines between the power management control ECU and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the power management control ECU and ID code box (immobiliser code ECU).


·

ID code box (immobiliser code ECU)

·

Power management control ECU

·

Wire harness or connector


Either condition is met:
·

Within 10 seconds of a hybrid control system start operation being performed (with park (P) selected and the brake pedal depressed, press the power switch while carrying the key). If there is a malfunction, the hybrid control system stops (communication begins within 3 seconds of the hybrid control system start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the power switch is turned on (IG) after reconnecting the cable to the negative (-) terminal of the auxiliary battery (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2799 -

WIRING DIAGRAM

B271006E05
0.7,1.965 0.908,2.139 0.208,0.174 10 L6 0.697,2.133 1.965,2.447 1.269,0.313 10 Power Management Control ECU 5.485,0.962 5.844,1.150 0.359,0.188 10 EFIO 5.485,1.42 5.844,1.607 0.359,0.188 10 EFII 1.503,0.962 1.715,1.150 0.212,0.188 10 IMI 1.433,1.432 1.714,1.619 0.282,0.188 10 IMO 1.797,0.884 1.977,1.057 0.179,0.173 10 21 1.797,1.332 1.977,1.505 0.179,0.173 10 20 5.301,0.876 5.402,1.086 0.101,0.210 10 6 5.301,1.359 5.402,1.569 0.101,0.210 10 5 5.089,1.956 5.470,2.142 0.381,0.186 10 L10 5.089,2.124 6.620,2.443 1.531,0.320 10 ID Code Box (Immobiliser Code ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or transmission control ECU, refer to the Service Bulletin.

·

The fixed 12 V power source voltage in the power management control ECU is output through a resistance from terminal IMI. The ID code box (immobiliser code ECU) grounds or does not ground this power source voltage accordingly.

·

The fixed 12 V power source voltage in the ID code box (immobiliser code ECU) is output through a resistance from terminal EFII. The power management control ECU grounds or does not ground this power source voltage accordingly.

·

After performing repair, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

When DTC B2799 and a DTC for the certification ECU (smart key ECU assembly) are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.




OK

NG

3.CHECK POWER MANAGEMENT CONTROL ECU (IMO)
3.CHECK POWER MANAGEMENT CONTROL ECU (IMO)
a.

Using an oscilloscope, check the waveform.

U154580E02
2.667,2.625 2.385,2.094 2.385,2.094 1.885,2.094 false 5.146,1.302 5.469,1.927 5.469,1.927 5.646,1.927 false 1.323,0.083 1.531,0.302 0.208,0.219 10 false *a 4.948,0.24 5.167,0.438 0.219,0.198 10 false L6 3.729,1.969 3.938,2.188 0.208,0.219 10 false *b 1.688,1.99 1.896,2.208 0.208,0.219 10 false *1 5.719,1.875 6.021,2.021 0.302,0.146 10 false IMO 1.521,3.292 1.875,3.49 0.354,0.198 10 false GND

Text in Illustration
*1 Waveform 1 - -
*a Component with harness connected
(Power Management Control ECU)
*b Normal Waveform

Measurement Condition
Item Content
Tester Connection L6-20 (IMO) - Body ground
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 has abnormal wavelength or shape B
Terminal IMO stuck high (12 V)
Terminal IMO stuck low (2.4 V or less) C



A

4.CHECK POWER MANAGEMENT CONTROL ECU (IMI)

B

7.REPLACE POWER MANAGEMENT CONTROL ECU

C

10.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (IMO)
4.CHECK POWER MANAGEMENT CONTROL ECU (IMI)
a.

Using an oscilloscope, check the waveform.

U154579E02
4.858,0.176 5.080,0.329 0.222,0.152 10 L6 3.976,1.974 4.198,2.127 0.222,0.152 10 *b 3.018,1.974 3.240,2.127 0.222,0.152 10 *1 1.29,0.074 1.512,0.226 0.222,0.152 10 *a 1.523,3.306 1.868,3.458 0.346,0.151 10 GND 3.97,2.503 3.685,2.059 3.685,2.059 3.199,2.059 false 5.604,1.859 5.839,2.030 0.235,0.172 10 IMI 5.063,1.289 5.324,1.929 5.324,1.929 5.576,1.929 false

Text in Illustration
*1 Waveform 2 - -
*a Component with harness connected
(Power Management Control ECU)
*b Normal Waveform

Measurement Condition
Item Content
Tester Connection L6-21 (IMI) - Body ground
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 2 not output, or has abnormal wavelength or shape B



A

5.REGISTER RECOGNITION CODES

B

12.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
5.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to the Service Bulletin.




NEXT

6.REGISTER ECU COMMUNICATION ID
6.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.


b.

Check that the hybrid control system can be started with a registered key.

HINT:

Refer to the Service Bulletin.


OK:

Hybrid control system can be started with a registered key.




OK

END (ECU COMMUNICATION ID WAS NOT REGISTERED CORRECTLY)

NG

7.REPLACE POWER MANAGEMENT CONTROL ECU
7.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Temporarily replace the power management control ECU with a new or known good one (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL).



NEXT

8.CLEAR DTC
8.CLEAR DTC

NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC is not output.




OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

NG

10.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (IMO)
a.

Disconnect the L6 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L6-20 (IMO) - Body ground Power switch on (IG) 11 to 14 V




A

11.CHECK HARNESS AND CONNECTOR (ID CODE BOX - POWER MANAGEMENT CONTROL ECU)

B

15.REPLACE POWER MANAGEMENT CONTROL ECU
11.CHECK HARNESS AND CONNECTOR (ID CODE BOX - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the L10 box connector.


b.

Disconnect the L6 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-5 (EFII) - L6-20 (IMO) Always Below 1 Ω
L6-20 (IMO) - Body ground Always 10 kΩ or higher




OK

12.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to the Service Bulletin.




NEXT

13.CLEAR DTC
13.CLEAR DTC

b.

Register the recognition codes in the ECUs.


c.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.




NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC is not output.




OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG

15.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Temporarily replace the power management control ECU with a new or known good one (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL).



NEXT

16.CLEAR DTC
16.CLEAR DTC

NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC is not output.




OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

NG