Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2015.08–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the power switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2784 The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Terminal VC5, TXCT or CODE is open (includes disconnection of the power switch).

·

The transponder key amplifier coil built into the power switch is open.


·

Power switch

·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)


With park (P) selected, the key is held against the power switch and a hybrid control system start operation is performed by pressing and holding the power switch when the transmitter battery is depleted.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when transmitter battery is depleted by holding key against power switch and pressing and holding power switch with park (P) selected -

Related Data List and Active Test
DTC Code Data List and Active Test
B2784 -

WIRING DIAGRAM

B271005E04
0.936,2.986 1.797,3.189 0.861,0.203 10 Power Switch 0.936,2.818 1.372,2.985 0.436,0.167 10 L43 1.45,1.175 1.869,1.325 0.419,0.151 10 CODE 1.482,2.095 1.869,2.248 0.387,0.153 10 TXCT 1.956,1.078 2.206,1.260 0.249,0.183 10 10 1.956,2.01 2.135,2.182 0.179,0.173 10 9 5.033,1.078 5.282,1.260 0.249,0.183 10 13 5.033,2.01 5.282,2.182 0.249,0.173 10 12 5.33,2.087 5.721,2.240 0.391,0.153 10 TXCT 5.027,2.986 6.586,3.292 1.559,0.306 10 Certification ECU (Smart Key ECU Assembly) 5.027,2.818 5.433,2.988 0.405,0.170 10 L62 5.344,1.184 5.777,1.347 0.434,0.163 10 CODE

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

The certification ECU (smart key ECU assembly) outputs a fixed 5 V power source voltage through a resistance from terminal CODE. The power switch grounds or does not ground this power source voltage accordingly.

·

The certification ECU (smart key ECU assembly) outputs a fixed 5 V power source voltage through a resistance and transistor. The power switch grounds or does not ground this signal accordingly.

·

After performing repair, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Perform the operation that fulfills the DTC output confirmation operation.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER SWITCH)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER SWITCH)
a.

Disconnect the L62 ECU connector.


b.

Disconnect the L43 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L62-13 (CODE) - L43-10 (CODE) Always Below 1 Ω
L62-12 (TXCT) - L43-9 (TXCT)
L62-13 (CODE) or L43-10 (CODE) - Body ground Always 10 kΩ or higher
L62-12 (TXCT) or L43-9 (TXCT) - Body ground




OK

4.REPLACE POWER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER SWITCH
a.

Temporarily replace the power switch with a new or known good one (See page Engine / Hybrid System>2ZR-FXE (STARTING)>POWER SWITCH>REMOVAL).



NEXT

5.CLEAR DTC
5.CLEAR DTC

NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Perform the operation that fulfills the DTC output confirmation operation.




OK

END (POWER SWITCH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)