Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the power switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2784 The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Terminal AGND, VC5, TXCT or CODE is open (includes disconnection of the power switch).

·

The transponder key amplifier coil built into the power switch is open.


·

Power switch

·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)


With the shift lever in P, the key held near the power switch and a hybrid control system start operation is performed by pressing and holding the power switch when the key battery is depleted.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when key battery is depleted by holding key near power switch and pressing and holding power switch with shift lever in P -

Related Data List and Active Test
DTC Code Data List and Active Test
B2784 -

WIRING DIAGRAM

B392719E05
0.833,2.844 2.667,3.042 1.833,0.198 10 false Power Switch 4.969,2.813 6.708,3.229 1.74,0.417 10 false Certification ECU (Smart Key ECU Assembly) 1.594,0.625 2.104,0.854 0.51,0.229 10 false VC5 1.51,1.146 2.021,1.375 0.51,0.229 10 false TXCT 1.479,1.656 1.99,1.885 0.51,0.229 10 false CODE 1.469,2.188 1.979,2.417 0.51,0.229 10 false AGND 5.313,0.615 5.823,0.844 0.51,0.229 10 false VC5 5.302,1.135 5.813,1.365 0.51,0.229 10 false TXCT 5.302,1.646 5.813,1.875 0.51,0.229 10 false CODE 5.302,2.156 5.813,2.385 0.51,0.229 10 false AGND 1.927,0.531 2.438,0.76 0.51,0.229 10 false 10 1.948,1.021 2.458,1.25 0.51,0.229 10 false 7 1.948,1.542 2.458,1.771 0.51,0.229 10 false 8 1.948,2.083 2.458,2.313 0.51,0.229 10 false 6 5.125,0.5 5.635,0.729 0.51,0.229 10 false 1 5.125,1.031 5.635,1.26 0.51,0.229 10 false 9 5.125,1.542 5.635,1.771 0.51,0.229 10 false 7 5.052,2.063 5.563,2.292 0.51,0.229 10 false 24 4.979,2.667 5.49,2.896 0.51,0.229 10 false L197 0.844,2.667 1.354,2.896 0.51,0.229 10 false L194

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

NG

3.CHECK POWER SWITCH (OUTPUT)
3.CHECK POWER SWITCH (OUTPUT)
a.

Using an oscilloscope, check the waveform.

U190932E02
1.475,0.985 1.840,1.123 0.365,0.139 10 L194 3.262,0.312 3.563,0.524 0.301,0.211 10 *b 0.544,0.798 0.845,1.009 0.301,0.211 10 *a 3.262,2.134 3.563,2.345 0.301,0.211 10 *c 1.006,2.841 1.436,2.980 0.430,0.139 10 CODE 6.496,1.34 6.926,1.479 0.430,0.139 10 GND 6.496,3.134 6.926,3.272 0.430,0.139 10 GND 1.639,2.147 1.639,2.911 1.639,2.911 1.443,2.911 false 2.211,2.854 2.826,2.993 0.615,0.139 10 AGND 1.873,2.16 1.873,2.924 1.873,2.924 2.144,2.924 false


Text in Illustration
*a Component with harness connected
(Power Switch)
*b Waveform
*c Waveform (detail) - -

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
L194-8 (CODE) - L194-6 (AGND) Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch* 1 V/DIV., 20 ms./DIV. Pulse generation
(See waveform)
2 V/DIV., 100 μs./DIV. Pulse generation
(See waveform (detail))


*: Remove the transmitter battery before performing this inspection.


OK:

The waveform is similar to that shown in the illustration



OK

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.




NEXT

5.REGISTER ECU COMMUNICATION ID
5.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR)

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) WAS DEFECTIVE)

NG