Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the power switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B278A A short to GND in the power supply of the transponder key amplifier of the power switch (VC5 - VC5) (1 trip detection logic*).
·

Wire harness or connector


·

Power switch


·

Certification ECU (smart key ECU assembly)


With park (P) selected, the key is held against the power switch and a hybrid control system start operation is performed by pressing and holding the power switch when the transmitter battery is depleted.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when transmitter battery is depleted by holding key against power switch and pressing and holding power switch with park (P) selected -

Related Data List and Active Test
DTC Code Data List and Active Test
B278A -

WIRING DIAGRAM

B271005E05
0.936,2.986 1.797,3.189 0.861,0.203 10 Power Switch 0.936,2.818 1.372,2.985 0.436,0.167 10 L43 1.581,1.175 1.870,1.325 0.290,0.151 10 VC5 1.447,2.095 1.869,2.248 0.422,0.153 10 AGND 1.956,1.078 2.206,1.260 0.249,0.183 10 14 1.956,2.01 2.135,2.182 0.179,0.173 10 8 5.033,1.078 5.282,1.260 0.249,0.183 10 28 5.033,2.01 5.282,2.182 0.249,0.173 10 36 5.33,2.087 5.756,2.240 0.426,0.153 10 AGND 5.027,2.986 6.586,3.292 1.559,0.306 10 Certification ECU (Smart Key ECU Assembly) 5.027,2.818 5.433,2.988 0.405,0.170 10 L62 5.344,1.184 5.632,1.347 0.288,0.163 10 VC5

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

The fixed 5 V power source voltage in the power switch is output through a resistance from terminal VC5.

·

Terminal AGND is grounded through both the power switch and certification ECU (smart key ECU assembly).

·

After performing repair, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER SWITCH)
a.

Disconnect the L62 ECU connector.


b.

Disconnect the L43 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L62-28 (VC5) - L43-14 (VC5) Always Below 1 Ω
L62-36 (AGND) - L43-8 (AGND)
L62-28 (VC5) or L43-14 (VC5) - Body ground Always 10 kΩ or higher
L62-36 (AGND) or L43-8 (AGND) - Body ground




OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B442002E02
0.167,0.958 0.563,1.208 0.396,0.25 0.802,1.75 1.177,1.438 true 2.521,1.74 2.167,1.438 true 2.927,3.646 3.365,3.875 0.438,0.229 10 false GND 2.521,1.771 3.031,2 0.51,0.229 10 false AGND 0.531,1.75 0.969,1.979 0.438,0.229 10 false VC5 0.26,1 0.698,1.229 0.438,0.229 10 false L43 0.177,0.135 0.615,0.365 0.438,0.229 10 false *a

Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the power switch side.


Measurement Condition
Item Content
Tester Connection L43-14 (VC5) - L43-8 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, key not in the cabin, within 30 seconds after power switch pressed

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Component with harness connected
(Power Switch)



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)