Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (IMI - EFIO) between the power management control ECU and ID code box (immobiliser code ECU) is stuck high, the power management control ECU stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B279A The communication line (IMI - EFIO) between the power management control ECU and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*).
·

Wire harness or connector (disconnection or break in wire harness is main cause)

·

ID code box (immobiliser code ECU)

·

Power management control ECU


Turn the power switch on (IG) and wait 6 seconds.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started Hybrid control system cannot be started

Related Data List and Active Test
DTC Code Data List and Active Test
B279A -

WIRING DIAGRAM

B271007E03
0.686,1.805 0.887,1.978 0.201,0.174 10 L6 0.686,1.969 1.951,2.307 1.266,0.337 10 Power Management Control ECU 5.486,0.986 5.837,1.160 0.352,0.174 10 EFIO 1.504,0.986 1.716,1.160 0.212,0.174 10 IMI 5.306,0.9 5.400,1.074 0.094,0.174 10 6 1.799,0.9 1.979,1.074 0.180,0.174 10 21 5.095,1.801 5.383,1.974 0.288,0.174 10 L10 5.095,1.951 6.627,2.258 1.532,0.306 10 ID Code Box (Immobiliser Code ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ID code box (immobiliser code ECU), refer to the Service Bulletin.

·

The fixed 12 V power source voltage in the power management control ECU is output through a resistance from terminal IMI. The ID code box (immobiliser code ECU) grounds or does not ground this power source voltage accordingly.

·

After performing repair, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the power switch on (IG) and wait 10 seconds.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B279A is output A
DTC B279A and other DTCs are output B

HINT:

If DTCs other than DTC B279A are output, troubleshoot those DTCs first.




A

3.CHECK CONNECTION OF CONNECTOR

B

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the power management control ECU and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX - POWER MANAGEMENT CONTROL ECU)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the L10 box connector.


b.

Disconnect the L6 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-6 (EFIO) - L6-21 (IMI) Always Below 1 Ω
L6-21 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L6-21 (IMI) - Body ground Always Below 1 V




OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to the Service Bulletin.




NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.REGISTER RECOGNITION CODES
7.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to the Service Bulletin.




NEXT

8.REGISTER ECU COMMUNICATION ID (ID CODE BOX - POWER MANAGEMENT CONTROL ECU)
8.REGISTER ECU COMMUNICATION ID (ID CODE BOX - POWER MANAGEMENT CONTROL ECU)
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.




NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A is not output.




OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG