Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2014.11
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301770 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horns to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B272452E04
0.396,0.865 0.667,1.094 0.271,0.229 10 false 1H 0.458,0.646 0.625,0.844 0.167,0.198 10 false 7 2.469,0.865 2.719,1.073 0.25,0.208 10 false 1G 2.49,0.656 2.708,0.854 0.219,0.198 10 false 18 2.469,1.406 2.74,1.656 0.271,0.25 10 false 1G 2.531,1.219 2.656,1.406 0.125,0.188 10 false 5 2.469,1.969 2.698,2.188 0.229,0.219 10 false 1G 2.531,1.781 2.667,2.01 0.135,0.229 10 false 6 4.802,0.667 5.01,0.854 0.208,0.188 10 false 24 5.896,0.656 6.177,0.875 0.281,0.219 10 false 28 4.792,1.26 5.083,1.469 0.292,0.208 10 false 33 1.906,0.854 2.375,1.042 0.469,0.188 10 false HNSW 1.938,1.417 2.406,1.625 0.469,0.208 10 false HRNH 1.958,1.979 2.385,2.219 0.427,0.24 10 false HRNL 0.719,0.865 1.135,1.063 0.417,0.198 10 false BATT 6.24,0.865 6.667,1.042 0.427,0.177 10 false HORN 5.479,3.208 7.125,3.615 1.646,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.104,4.031 6.563,4.458 1.458,0.427 10 false to Steering Pad Switch Assembly 4.854,1.896 5.927,2.438 1.073,0.542 10 false Instrument Panel Junction Block Assembly 0.802,2.427 2.25,2.646 1.448,0.219 10 false No. 1 Integration Relay 3.125,4.292 3.375,4.479 0.25,0.188 10 false A3 3.844,4.51 3.938,4.646 0.094,0.135 10 false 1 2.844,4.51 2.938,4.646 0.094,0.135 10 false 1 3.125,4.448 3.781,5.177 0.656,0.729 10 false Low Pitched Horn Assembly 4.125,4.281 4.448,4.5 0.323,0.219 10 false A1 4.125,4.427 4.823,5.208 0.698,0.781 10 false High Pitched Horn Assembly 0.813,4.042 2.167,4.271 1.354,0.229 10 false from Auxiliary Battery 4.792,0.865 5.281,1.094 0.49,0.229 10 false 2C 4.792,1.458 5.156,1.74 0.365,0.281 10 false 2A 5.875,0.875 6.292,1.115 0.417,0.24 10 false MB

PROCEDURE

1.INSPECT HORNS
a.

Press the horn switch and check if the horns sound.

Result:
Result Proceed to
Horns sound A
Horns do not sound B




A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Vehicle Horn Vehicle horns ON / OFF -

Result:
Result Proceed to
The vehicle horns do not sound when operated through the GTS A
The vehicle horns sound and stop correctly when operated through the GTS B




A

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U110784E01
1.651,0.392 1.847,0.530 0.195,0.137 10 2C 0.172,0.15 0.326,0.300 0.154,0.150 10 *a 5.037,0.536 5.266,0.673 0.230,0.137 10 MB 5.773,1.306 6.200,1.448 0.427,0.142 10 HORN 6.413,1.087 6.413,1.374 6.413,1.374 6.216,1.374 false


b.

Disconnect the 2C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-24 - MB-28 (HORN) Always Below 1 Ω
2C-24 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY