Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.08–2016.05
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  U0100  Lost Communication with ECM / PCM "A"  U0129  Lost Communication with Skid Control ECU  U0131  Lost Communication with Power Steering Control Module  U0142  Lost Communication with Body Control Module "B"  U0151  Lost Communication with Airbag ECU  U0163  Lost Communication with Navigation Control Module  U023A  Lost Communication with Front Camera Module  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The combination meter sub-assembly communicates with the ECM or power management control ECU, brake booster with master cylinder assembly (skid control ECU), power steering ECU assembly, main body ECU (multiplex network body ECU), airbag ECU assembly, navigation receiver assembly*1, lane departure warning camera*2 and driving support ECU assembly*3 via CAN communication.

DTC No. DTC Detection Condition Trouble Area
U0100 When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with ECM or power management control ECU continues for 2 seconds or more


·

ECM

·

Power management control ECU

·

CAN communication system

·

Combination meter sub-assembly


U0129 When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with brake booster with master cylinder assembly (Skid control ECU) continues for 3 seconds or more


·

Brake booster with master cylinder assembly (Skid control ECU)

·

CAN communication system

·

Combination meter sub-assembly


U0131 When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with power steering ECU assembly continues for 3 seconds or more


·

Power steering ECU assembly

·

CAN communication system

·

Combination meter sub-assembly


U0142 When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with main body ECU (multiplex network body ECU) continues for 3 seconds or more


·

Main body ECU (Multiplex network body ECU)

·

CAN communication system

·

Combination meter sub-assembly


U0151 When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with airbag ECU assembly continues for 10 seconds or more


·

Airbag ECU assembly

·

CAN communication system

·

Combination meter sub-assembly


U0163*1 When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with navigation receiver assembly continues for 3 seconds or more


·

Navigation receiver assembly

·

CAN communication system

·

Combination meter sub-assembly


U023A*2 When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with lane departure warning camera continues for 10 seconds or more


·

Lane departure warning camera

·

CAN communication system

·

Combination meter sub-assembly


U1104*3 When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with driving support ECU assembly continues for 10 seconds or more


·

Driving support ECU assembly

·

CAN communication system

·

Combination meter sub-assembly



*1: for Navigation receiver type

*2: w/ Lane departure alert system

*3: w/ Dynamic radar cruise control system


PROCEDURE

1.CONFIRM DTC OUTPUT
a.

Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B




A

B