Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter sub-assembly detects a fuel sender gauge malfunction via a direct line.

DTC No. DTC Detection Condition Trouble Area
B1500 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Fuel sender gauge operation malfunction


·

Harness or connector

·

Fuel sender gauge assembly

·

Combination meter sub-assembly (Meter circuit plate)



WIRING DIAGRAM

E230580E54
4.917,3.063 7.01,3.469 2.094,0.406 10 false Combination Meter Sub-assembly (Meter Circuit Plate) 5.75,0.979 5.854,1.135 0.104,0.156 10 false L 5.75,2.344 6.156,2.5 0.406,0.156 10 false ES 2 5.479,0.844 5.656,0.99 0.177,0.146 10 false 12 5.469,2.208 5.646,2.354 0.177,0.146 10 false 13 2.323,2.208 2.438,2.354 0.115,0.146 10 false 3 2.323,0.844 2.438,0.99 0.115,0.146 10 false 2 0.646,3.146 2.417,3.51 1.771,0.365 10 false Fuel Suction with Pump and Gauge Tube Assembly 0.792,1.375 1.427,2.042 0.635,0.667 10 false Fuel Sender Gauge Assembly 1.667,1.313 1.781,1.458 0.115,0.146 10 false 2 1.667,2.01 1.781,2.156 0.115,0.146 10 false 1 2.042,2.198 2.26,2.344 0.219,0.146 10 false FE 2.042,0.854 2.24,1.01 0.198,0.156 10 false FS 4.917,2.906 5.25,3.052 0.333,0.146 10 false L27 0.646,2.99 0.927,3.135 0.281,0.146 10 false R11

PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input/Min.: 0, Max.: 127.5 10th segment comes on:
39.8 to 45.0
Unit: Liter
9th segment comes on:
36.2 to 39.8
8th segment comes on:
32.6 to 36.2
7th segment comes on:
28.6 to 32.6
6th segment comes on:
24.4 to 28.6
5th segment comes on:
20.1 to 24.4
4th segment comes on:
16.0 to 20.1
3rd segment comes on:
12.5 to 16.0
2nd segment comes on:
8.6 to 12.5
1st segment comes on:
4.8 to 8.6

Result:
Result Proceed to
Fuel level data can be displayed on the GTS. A
Fuel level data cannot be displayed on the GTS. B




A

B

2.INSPECT FUEL SENDER GAUGE ASSEMBLY
2.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
U155024E01
0.242,0.223 0.422,0.407 0.179,0.184 10 *a 0.859,1.315 1.157,1.496 0.298,0.181 10 L27 2.678,1.531 2.826,1.678 0.148,0.146 10 L 2.932,1.845 3.313,2.023 0.381,0.178 10 ES 2 2.614,1.64 1.92,2.35 false 2.034,2.351 2.896,1.952 false

Disconnect the L27 combination meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-12 (L) - L27-13 (ES 2) Always 12 to 415 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)



OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)
a.

Disconnect the R11 fuel suction with pump and gauge tube assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-12 (L) - R11-2 (FS) Always Below 1 Ω
L27-12 (L) - Body ground Always 10 kΩ or higher
L27-13 (ES 2) - R11-3 (FE) Always Below 1 Ω
L27-13 (ES 2) - Body ground Always 10 kΩ or higher




OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


A255977E02
0.219,0.094 2.052,1.677 1.833,1.583 1.646,4.135 0.844,4.135 false 1.729,2.458 0.813,2.458 false 0.667,4.052 0.865,4.229 0.198,0.177 10 false E 0.656,2.375 0.854,2.552 0.198,0.177 10 false F 0.281,0.188 0.479,0.365 0.198,0.177 10 false *a

b.

Check that the float moves smoothly between E and F.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float level is F (upper) 12 to 18 Ω
1 - 2 Float level is between F (upper) and E (lower) 12 to 415 Ω (Gradually changes)
1 - 2 Float level is E (lower) 405 to 415 Ω


Text in Illustration
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)



OK

NG