Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When multiple warning lights in the combination meter blink continuously, a ground short in the wiring or an ECU connected to terminal TC of the DLC3 is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the airbag ECU assembly. Thus when multiple systems do not enter DTC output mode, there may be a hybrid vehicle control ECU malfunction.



WIRING DIAGRAM

C248718E71
0.24,4.083 2.354,4.323 2.115,0.24 10 false Hybrid Vehicle Control ECU 0.25,3.906 0.74,4.156 0.49,0.25 10 false L6 1.375,1.24 1.667,1.677 0.292,0.438 10 false 24 1.375,0.542 1.656,0.823 0.281,0.281 10 false 25 1.396,2.656 1.938,3.063 0.542,0.406 10 false 28 0.927,1.396 1.448,1.865 0.521,0.469 10 false CANL 0.906,0.688 1.448,1.115 0.542,0.427 10 false CANH 5.958,2.75 6.292,3.021 0.333,0.271 10 false TC 1.115,2.76 1.521,3.042 0.406,0.281 10 false TC 5.719,2.656 6.052,2.969 0.333,0.313 10 false 13 5.802,3.281 6.104,3.531 0.302,0.25 10 false 4 5.958,3.375 6.302,3.667 0.344,0.292 10 false CG 6.167,3.917 6.646,4.333 0.479,0.417 10 false L61 6.125,4.083 6.708,4.5 0.583,0.417 10 false DLC3 5.958,1.385 6.427,1.646 0.469,0.26 10 false CANL 5.635,1.844 6.042,2.104 0.406,0.26 10 false F16 5.719,1.25 6.01,1.521 0.292,0.271 10 false 22 5.719,0.542 6.052,0.792 0.333,0.25 10 false 13 5.958,0.677 6.479,1.094 0.521,0.417 10 false CANH 5.635,2.01 7.104,2.385 1.469,0.375 10 false Airbag ECU Assembly 0.75,4.438 2.573,4.708 1.823,0.271 10 false : CAN Communication Line

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF HYBRID VEHICLE CONTROL ECU)
a.
U191167E02
2.083,1.469 2.458,1.906 false 1.865,3.979 1.427,4.375 false 0.167,0.177 0.385,0.365 0.219,0.188 10 false *1 0.302,1.104 0.604,1.313 0.302,0.208 10 false L61 2.417,1.927 2.688,2.115 0.271,0.188 10 false TC 0.188,2.438 0.406,2.625 0.219,0.188 10 false *a 0.427,3.438 0.698,3.625 0.271,0.188 10 false L6 1.26,4.375 1.531,4.563 0.271,0.188 10 false TC

Turn the power switch off.


b.

Disconnect the connector from the hybrid vehicle control ECU.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-13 (TC) - L6-28 (TC) Always Below 1 Ω


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)



OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
U154734E01
0.054,0.066 0.202,0.206 0.149,0.140 10 *1 1.845,0.204 2.072,0.341 0.227,0.137 10 CG 0.2,0.561 0.451,0.717 0.251,0.156 10 L61 1.616,0.814 1.616,0.292 1.616,0.292 1.802,0.292 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*1 DLC3



OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
U154735E01
0.054,0.065 0.202,0.205 0.149,0.140 10 *1 2.03,1.775 2.257,1.912 0.227,0.137 10 TC 1.805,1.339 1.805,1.861 1.805,1.861 1.991,1.861 false 0.213,0.582 0.461,0.735 0.248,0.153 9 L61

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-13 (TC) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 DLC3



OK

NG

REPAIR OR REPLACE WIRE HARNESS OR REPLACE EACH ECU