Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the airbag ECU assembly and instrument panel passenger airbag assembly.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1805/52
·

The airbag ECU assembly receives a line short circuit signal in the front passenger side squib circuit during primary check.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 3 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag ECU assembly


B1806/52
·

The airbag ECU assembly receives an open circuit signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


B1807/52
·

The airbag ECU assembly receives a short circuit to ground signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


B1808/52
·

The airbag ECU assembly receives a short circuit to B+ signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C351803E16
0.688,2.5 1.479,2.885 0.792,0.385 10 false H3 0.688,2.656 3.5,3.188 2.813,0.531 10 false Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib) 2.146,1.885 2.938,2.271 0.792,0.385 10 false P- 2.146,1.052 2.938,1.438 0.792,0.385 10 false P+ 2.406,1.052 3.198,1.438 0.792,0.385 10 false 1 2.406,1.885 3.198,2.271 0.792,0.385 10 false 2 3.375,1.167 4.167,1.552 0.792,0.385 10 false LH2 4.5,1.042 5.292,1.427 0.792,0.385 10 false 4 4.5,1.885 5.292,2.271 0.792,0.385 10 false 3 4.708,3.188 6.51,3.615 1.802,0.427 10 false Airbag ECU Assembly 4.719,3.021 5.51,3.406 0.792,0.385 10 false L16 3.375,2 4.167,2.385 0.792,0.385 10 false LH2 4.708,1.156 5.5,1.542 0.792,0.385 10 false P+ 4.688,2 5.479,2.385 0.792,0.385 10 false P- 3.417,0.958 4.208,1.344 0.792,0.385 10 false 1 3.448,1.802 4.24,2.188 0.792,0.385 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241746E07
0.191,1.439 0.347,1.591 0.156,0.152 10 *1 0.622,0.398 0.789,0.563 0.167,0.165 10 *3 2.713,1.146 2.887,1.302 0.174,0.156 10 *2 2.261,0.838 2.378,0.991 0.117,0.153 10 A 1.95,0.838 2.067,0.991 0.117,0.153 10 B 1.47,0.838 1.597,0.991 0.127,0.153 10 C 1.16,0.838 1.287,0.991 0.127,0.153 10 D 0.685,0.838 0.812,0.991 0.127,0.153 10 E 0.388,0.838 0.515,0.991 0.127,0.153 10 F 0.274,0.992 0.274,1.426 false 1.698,1.439 1.854,1.591 0.156,0.152 10 *4 1.781,0.992 1.781,1.426 false 0.982,0.86 0.982,0.487 0.982,0.487 0.818,0.487 false

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag ECU assembly. Also check that the connectors that link the instrument panel wire and No. 3 instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the instrument panel passenger airbag assembly and airbag ECU assembly. Also disconnect the instrument panel wire from the No. 3 instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the No. 3 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the instrument panel wire and No. 3 instrument panel wire with the activation prevention mechanism are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 No. 3 Instrument Panel Wire
*4 Instrument Panel Wire



OK

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

NG

REPLACE WIRE HARNESS

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
a.
U191116E02
0.385,0.667 0.385,0.927 false 1.76,2.229 2.042,2.229 false 0.302,0.938 0.458,1.094 0.156,0.156 10 false *1 0.344,1.688 0.51,1.854 0.167,0.167 10 false *a 2.073,2.146 2.385,2.292 0.313,0.146 10 false SST 2.594,0.802 2.771,0.958 0.177,0.156 10 false *2 2.177,0.51 2.292,0.667 0.115,0.156 10 false A 2.021,0.51 2.135,0.667 0.115,0.156 10 false B 1.531,0.51 1.656,0.667 0.125,0.156 10 false C 1.375,0.51 1.5,0.667 0.125,0.156 10 false D 0.906,0.51 1.031,0.667 0.125,0.156 10 false E 0.5,0.51 0.625,0.667 0.125,0.156 10 false F 0.49,2.427 0.729,2.583 0.24,0.156 10 false H3

Connect the instrument panel wire to the No. 3 instrument panel wire and airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.

Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.
U191079E02
0.375,0.667 0.375,0.958 false 1.469,2.083 1.156,2.083 true 1.979,2.094 1.667,2.094 true 0.5,0.49 0.604,0.646 0.104,0.156 10 false F 0.802,0.49 0.927,0.646 0.125,0.156 10 false E 1.26,0.49 1.385,0.646 0.125,0.156 10 false D 1.417,0.49 1.542,0.646 0.125,0.156 10 false C 1.865,0.49 1.99,0.646 0.125,0.156 10 false B 2.167,0.49 2.292,0.646 0.125,0.156 10 false A 0.302,0.958 0.458,1.135 0.156,0.177 10 false *1 2.563,0.771 2.74,0.917 0.177,0.146 10 false *2 0.281,1.74 0.458,1.906 0.177,0.167 10 false *a 2.01,2.01 2.188,2.156 0.177,0.146 10 false P- 0.938,2 1.146,2.146 0.208,0.146 10 false P+ 0.792,2.344 1,2.49 0.208,0.146 10 false H3

Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H3-1 (P+) - Body ground Power switch on (IG) Below 1 V
H3-2 (P-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-1 (P+) - H3-2 (P-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-1 (P+) - Body ground Always 1 MΩ or higher
H3-2 (P-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-1 (P+) - H3-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C238235E07
0.51,0.875 0.51,1.167 false 0.625,0.719 0.729,0.875 0.104,0.156 10 false F 0.781,0.719 0.906,0.875 0.125,0.156 10 false E 1.229,0.719 1.354,0.875 0.125,0.156 10 false D 1.396,0.719 1.521,0.875 0.125,0.156 10 false C 1.833,0.719 1.958,0.875 0.125,0.156 10 false B 1.99,0.719 2.115,0.875 0.125,0.156 10 false A 0.427,1.188 0.583,1.365 0.156,0.177 10 false *1 2.396,0.99 2.573,1.135 0.177,0.146 10 false *2

Connect the connectors to the instrument panel passenger airbag assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.
U191080E01
0.424,0.487 0.533,0.639 0.109,0.153 10 F 0.733,0.487 0.854,0.639 0.121,0.153 10 E 1.179,0.487 1.300,0.639 0.121,0.153 10 D 1.494,0.487 1.615,0.639 0.121,0.153 10 C 1.949,0.487 2.070,0.639 0.121,0.153 10 B 2.264,0.487 2.385,0.639 0.121,0.153 10 A 0.21,0.939 0.362,1.114 0.152,0.175 10 *1 2.658,0.786 2.835,0.930 0.176,0.144 10 *2 0.384,1.735 0.558,1.900 0.174,0.165 10 *a 2.09,2.89 2.267,3.038 0.177,0.148 10 P- 0.295,0.645 0.295,0.93 false 0.93,0.939 1.082,1.114 0.152,0.175 10 *3 1.015,0.645 1.015,0.93 false 1.209,2.89 1.418,3.041 0.209,0.151 10 P+ 1.659,2.621 1.34,2.859 false 1.839,2.621 2.157,2.859 false 1.362,0.047 1.514,0.222 0.152,0.175 10 *4 1.779,0.498 1.779,0.129 1.779,0.129 1.544,0.129 false 0.696,2.253 0.971,2.409 0.276,0.156 10 LH2

Disconnect the No. 3 instrument panel wire from the instrument panel wire.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
LH2-1 (P+) - Body ground Power switch on (IG) Below 1 V
LH2-2 (P-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
LH2-1 (P+) - LH2-2 (P-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
LH2-1 (P+) - Body ground Always 1 MΩ or higher
LH2-2 (P-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
LH2-1 (P+) - LH2-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 No. 3 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to No. 3 Instrument Panel Wire)




OK

6.CHECK NO. 3 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK NO. 3 INSTRUMENT PANEL WIRE
a.
U191081E02
0.302,0.656 0.302,0.948 false 1.771,0.667 1.771,0.958 false 1.469,2.094 1.115,2.094 true 2.042,2.094 1.677,2.094 true 1.021,0.5 1.021,0.198 1.021,0.198 1.177,0.198 false 0.438,0.5 0.542,0.656 0.104,0.156 10 false F 0.74,0.5 0.865,0.656 0.125,0.156 10 false E 1.188,0.5 1.313,0.656 0.125,0.156 10 false D 1.49,0.5 1.615,0.656 0.125,0.156 10 false C 1.948,0.5 2.073,0.656 0.125,0.156 10 false B 2.26,0.49 2.385,0.646 0.125,0.156 10 false A 0.229,0.948 0.385,1.125 0.156,0.177 10 false *1 2.656,0.74 2.833,0.885 0.177,0.146 10 false *2 0.313,1.75 0.49,1.917 0.177,0.167 10 false *a 2.073,2.021 2.25,2.167 0.177,0.146 10 false P- 1.698,0.958 1.854,1.135 0.156,0.177 10 false *4 0.906,2.01 1.115,2.156 0.208,0.146 10 false P+ 0.656,2.365 0.854,2.542 0.198,0.177 10 false H3 1.208,0.125 1.365,0.302 0.156,0.177 10 false *3

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H3-1 (P+) - Body ground Power switch on (IG) Below 1 V
H3-2 (P-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-1 (P+) - H3-2 (P-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-1 (P+) - Body ground Always 1 MΩ or higher
H3-2 (P-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-1 (P+) - H3-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.

Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 No. 3 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)




OK

NG

REPLACE NO. 3 INSTRUMENT PANEL WIRE