Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.08–2016.05
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825/56  Short in Side Squib LH Circuit  B1826/56  Open in Side Squib LH Circuit  B1827/56  Short to GND in Side Squib LH Circuit  B1828/56  Short to B+ in Side Squib LH Circuit  


DESCRIPTION

The front side squib LH circuit consists of the airbag ECU assembly and front seat airbag assembly LH.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1825/56
·

The airbag ECU assembly receives a line short circuit signal in the front side squib LH circuit during primary check.

·

Front side squib LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front seat airbag assembly LH (Front side squib LH)

·

Airbag ECU assembly


B1826/56
·

The airbag ECU assembly receives an open circuit signal in the front side squib LH circuit.

·

Front side squib LH malfunction

·

Airbag ECU assembly malfunction


B1827/56
·

The airbag ECU assembly receives a short circuit to ground signal in the front side squib LH circuit.

·

Front side squib LH malfunction

·

Airbag ECU assembly malfunction


B1828/56
·

The airbag ECU assembly receives a short circuit to B+ signal in the front side squib LH circuit.

·

Front side squib LH malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C239249E32
0.695,2.493 0.976,2.655 0.281,0.163 10 R3 0.695,2.659 2.693,3.011 1.998,0.351 10 Front Seat Airbag Assembly LH (Front Side Squib LH) 4.648,3.009 5.015,3.154 0.367,0.145 10 R1 4.703,1.986 5.086,2.149 0.384,0.163 10 SFL- 4.46,1.905 4.632,2.068 0.172,0.163 10 10 4.703,1.142 5.198,1.304 0.496,0.163 10 SFL+ 1.973,1.905 2.500,2.068 0.526,0.163 10 SFL- 1.973,1.065 2.436,1.228 0.463,0.163 10 SFL+ 4.536,1.065 4.633,1.228 0.097,0.163 10 9 2.41,1.905 2.521,2.068 0.111,0.163 10 2 2.41,1.065 2.521,1.228 0.111,0.163 10 1 4.648,3.188 6.282,3.364 1.634,0.176 10 Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241752E07
0.637,0.972 0.758,1.125 0.121,0.153 10 D 1.044,0.972 1.164,1.125 0.121,0.153 10 C 1.622,0.972 1.743,1.125 0.121,0.153 10 B 2.025,0.972 2.146,1.125 0.121,0.153 10 A 2.47,0.979 2.646,1.154 0.177,0.175 10 *2 0.45,1.577 0.602,1.730 0.152,0.152 10 *1 0.526,1.119 0.526,1.56 false 1.638,0.473 1.790,0.625 0.152,0.152 10 *3 1.387,0.987 1.387,0.563 1.387,0.563 1.613,0.563 false

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat airbag assembly LH and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat airbag assembly LH and airbag ECU assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire



OK

2.CHECK FRONT SEAT AIRBAG ASSEMBLY LH (FRONT SIDE SQUIB LH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT AIRBAG ASSEMBLY LH (FRONT SIDE SQUIB LH)
a.
U191117E01
0.459,2.362 0.664,2.507 0.204,0.144 10 R3 0.766,0.661 0.887,0.813 0.121,0.153 10 D 1.147,0.661 1.267,0.813 0.121,0.153 10 C 1.705,0.661 1.826,0.813 0.121,0.153 10 B 1.864,0.661 1.984,0.813 0.121,0.153 10 A 2.296,0.659 2.473,0.834 0.177,0.175 10 *2 0.587,1.181 0.740,1.357 0.152,0.175 10 *1 0.353,1.833 0.527,1.998 0.174,0.165 10 *a 2.064,2.449 2.352,2.607 0.288,0.158 10 SST 1.835,2.521 2.024,2.521 false 0.667,0.811 0.667,1.17 false

Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag assembly LH (front side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.


HINT:

Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.

Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
U191118E01
0.685,2.145 0.888,2.289 0.203,0.144 10 R3 0.662,0.746 0.783,0.898 0.121,0.153 10 D 1.063,0.746 1.184,0.898 0.121,0.153 10 C 1.585,0.746 1.706,0.898 0.121,0.153 10 B 1.975,0.746 2.096,0.898 0.121,0.153 10 A 2.402,0.749 2.579,0.924 0.177,0.175 10 *2 0.472,1.357 0.624,1.532 0.152,0.175 10 *1 0.315,1.719 0.489,1.884 0.174,0.165 10 *a 1.948,2.49 2.365,2.637 0.417,0.148 10 SFL- 0.63,2.49 1.014,2.640 0.384,0.151 10 SFL+ 1.397,2.574 1.104,2.574 false 1.912,2.574 1.62,2.574 false 0.559,0.898 0.559,1.346 false 1.553,0.302 1.705,0.477 0.152,0.175 10 *3 1.38,0.766 1.38,0.384 1.38,0.384 1.535,0.384 false

Disconnect the floor wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R3-1 (SFL+) - Body ground Power switch on (IG) Below 1 V
R3-2 (SFL-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R3-1 (SFL+) - R3-2 (SFL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R3-1 (SFL+) - Body ground Always 1 MΩ or higher
R3-2 (SFL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R3-1 (SFL+) - R3-2 (SFL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238245E01
0.762,1.589 0.918,1.740 0.156,0.152 10 *1 2.147,0.987 2.322,1.143 0.174,0.156 10 *2 1.73,0.987 1.847,1.140 0.117,0.153 10 A 1.572,0.987 1.689,1.140 0.117,0.153 10 B 1.119,0.987 1.246,1.140 0.127,0.153 10 C 0.962,0.987 1.089,1.140 0.127,0.153 10 D 0.845,1.142 0.845,1.575 false

Connect the connectors to the front seat airbag assembly LH and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.


HINT:

Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly



OK

NG