The airbag cut off switch circuit consists of the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.
The front passenger airbag can be optionally deactivated via this circuit by turning the airbag cut off switch cylinder sub-assembly to the OFF position.
If the front passenger airbag are deactivated, the passenger airbag ON/OFF indicator ("OFF") comes on to inform the passengers.
DTC B1651/33 is stored when a malfunction is detected in the airbag cut off switch circuit.
| DTC No. | DTC Detecting Condition | Trouble Area |
|---|---|---|
| B1651/33 | ·
The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the airbag cut off switch circuit. ·
Airbag cut off switch cylinder sub-assembly malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Airbag cut off switch cylinder sub-assembly ·
Airbag ECU assembly |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Terminals L16-11 (MSW+) and L16-12 (MSW-) of the airbag ECU assembly in this circuit have an activation prevention mechanism.
This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), this mechanism should be released.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connector and proceed to the next inspection.
Disconnect the connectors from the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.
The short spring is not deformed or damaged.
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L148-2 (PMC+) - L148-1 (PMC-) | Always | Below 1 Ω |
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly) |
OK
NG
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L148-2 (PMC+) - L148-1 (PMC-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly) |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L148-2 (PMC+) - Body ground | Power switch on (IG) | Below 1 V |
| L148-1 (PMC-) - Body ground | Power switch on (IG) | Below 1 V |
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly) |
OK
NG
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L148-2 (PMC+) - Body ground | Always | 1 MΩ or higher |
| L148-1 (PMC-) - Body ground | Always | 1 MΩ or higher |
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L148-2 (PMC+) - L148-1 (PMC-) | Cut off switch is ON | 360 to 440 Ω |
| L148-2 (PMC+) - L148-1 (PMC-) | Cut off switch is OFF | 90 to 110 Ω |
| *a | Component without harness connected
(Airbag Cut Off Switch Cylinder Sub-assembly) |
OK
NG
Connect the connectors to the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1651/33 is not output.
Codes other than DTC B1651/33 may be output at this time, but they are not related to this check.
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag ECU Assembly |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG