Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.11–2015.08
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1651/33  Manual Cut off Switch Trouble  


DESCRIPTION

The airbag cut off switch circuit consists of the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.

The front passenger airbag can be optionally deactivated via this circuit by turning the airbag cut off switch cylinder sub-assembly to the OFF position.

If the front passenger airbag are deactivated, the passenger airbag ON/OFF indicator ("OFF") comes on to inform the passengers.

DTC B1651/33 is stored when a malfunction is detected in the airbag cut off switch circuit.

DTC No. DTC Detecting Condition Trouble Area
B1651/33
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the airbag cut off switch circuit.

·

Airbag cut off switch cylinder sub-assembly malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Airbag cut off switch cylinder sub-assembly

·

Airbag ECU assembly



WIRING DIAGRAM

C263693E25
5.354,0.688 5.76,1.042 0.406,0.354 10 false 11 5.354,2.167 5.76,2.521 0.406,0.354 10 false 12 5.604,0.792 6.135,1.167 0.531,0.375 10 false MSW+ 5.604,2.271 6.135,2.646 0.531,0.375 10 false MSW- 5.552,2.938 5.958,3.292 0.406,0.354 10 false L16 5.552,3.104 7.104,3.542 1.552,0.438 10 false Airbag ECU Assembly 0.573,3.104 2.438,3.542 1.865,0.438 10 false Airbag Cut Off Switch Cylinder Sub-assembly 0.583,2.938 0.99,3.292 0.406,0.354 10 false L148 2.875,0.677 3.281,1.031 0.406,0.354 10 false 2 2.875,2.156 3.281,2.51 0.406,0.354 10 false 1 2.385,0.677 2.865,1.031 0.479,0.354 10 false PMC+ 2.417,2.156 2.896,2.51 0.479,0.354 10 false PMC-

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

Terminals L16-11 (MSW+) and L16-12 (MSW-) of the airbag ECU assembly in this circuit have an activation prevention mechanism.

This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), this mechanism should be released.


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

2.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U191143E01
1.29,0.533 1.422,0.689 0.132,0.157 10 C 0.885,0.533 1.017,0.689 0.132,0.157 10 D 1.754,0.533 1.885,0.689 0.132,0.157 10 B 2.166,0.533 2.298,0.689 0.132,0.157 10 A 0.567,0.528 0.750,0.720 0.183,0.192 10 *1 1.064,2.303 1.423,2.460 0.359,0.158 10 L148 2.26,2.901 2.678,3.058 0.417,0.158 10 PMC+ 1.618,2.898 2.015,3.056 0.397,0.158 10 PMC- 1.588,0.551 1.588,0.233 1.588,0.233 1.692,0.233 false 2.583,0.809 2.766,1.001 0.183,0.192 10 *2 1.727,0.161 1.910,0.353 0.183,0.192 10 *3 0.782,1.624 0.965,1.817 0.183,0.192 10 *a 2.283,2.63 2.46,2.91 false 1.854,2.901 2.03,2.622 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - L148-1 (PMC-) Always Below 1 Ω


Text in Illustration
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)



OK

3.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U191143E01
1.29,0.533 1.422,0.689 0.132,0.157 10 C 0.885,0.533 1.017,0.689 0.132,0.157 10 D 1.754,0.533 1.885,0.689 0.132,0.157 10 B 2.166,0.533 2.298,0.689 0.132,0.157 10 A 0.567,0.528 0.750,0.720 0.183,0.192 10 *1 1.064,2.303 1.423,2.460 0.359,0.158 10 L148 2.26,2.901 2.678,3.058 0.417,0.158 10 PMC+ 1.618,2.898 2.015,3.056 0.397,0.158 10 PMC- 1.588,0.551 1.588,0.233 1.588,0.233 1.692,0.233 false 2.583,0.809 2.766,1.001 0.183,0.192 10 *2 1.727,0.161 1.910,0.353 0.183,0.192 10 *3 0.782,1.624 0.965,1.817 0.183,0.192 10 *a 2.283,2.63 2.46,2.91 false 1.854,2.901 2.03,2.622 false

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - L148-1 (PMC-) Always 1 MΩ or higher



c.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)



OK

4.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U191143E01
1.29,0.533 1.422,0.689 0.132,0.157 10 C 0.885,0.533 1.017,0.689 0.132,0.157 10 D 1.754,0.533 1.885,0.689 0.132,0.157 10 B 2.166,0.533 2.298,0.689 0.132,0.157 10 A 0.567,0.528 0.750,0.720 0.183,0.192 10 *1 1.064,2.303 1.423,2.460 0.359,0.158 10 L148 2.26,2.901 2.678,3.058 0.417,0.158 10 PMC+ 1.618,2.898 2.015,3.056 0.397,0.158 10 PMC- 1.588,0.551 1.588,0.233 1.588,0.233 1.692,0.233 false 2.583,0.809 2.766,1.001 0.183,0.192 10 *2 1.727,0.161 1.910,0.353 0.183,0.192 10 *3 0.782,1.624 0.965,1.817 0.183,0.192 10 *a 2.283,2.63 2.46,2.91 false 1.854,2.901 2.03,2.622 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - Body ground Power switch on (IG) Below 1 V
L148-1 (PMC-) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)



OK

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U191143E01
1.29,0.533 1.422,0.689 0.132,0.157 10 C 0.885,0.533 1.017,0.689 0.132,0.157 10 D 1.754,0.533 1.885,0.689 0.132,0.157 10 B 2.166,0.533 2.298,0.689 0.132,0.157 10 A 0.567,0.528 0.750,0.720 0.183,0.192 10 *1 1.064,2.303 1.423,2.460 0.359,0.158 10 L148 2.26,2.901 2.678,3.058 0.417,0.158 10 PMC+ 1.618,2.898 2.015,3.056 0.397,0.158 10 PMC- 1.588,0.551 1.588,0.233 1.588,0.233 1.692,0.233 false 2.583,0.809 2.766,1.001 0.183,0.192 10 *2 1.727,0.161 1.910,0.353 0.183,0.192 10 *3 0.782,1.624 0.965,1.817 0.183,0.192 10 *a 2.283,2.63 2.46,2.91 false 1.854,2.901 2.03,2.622 false

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - Body ground Always 1 MΩ or higher
L148-1 (PMC-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)



OK

6.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY
a.
U191145E01
0.225,0.162 0.422,0.385 0.198,0.223 10 *a 2.75,0.743 3.162,0.899 0.412,0.157 10 PMC+ 2.75,1.198 3.137,1.355 0.387,0.157 10 PMC- 2.331,1.039 2.737,0.834 false 2.332,1.125 2.739,1.282 false 2.773,0.421 3.123,0.584 0.350,0.163 10 L148

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - L148-1 (PMC-) Cut off switch is ON 360 to 440 Ω
L148-2 (PMC+) - L148-1 (PMC-) Cut off switch is OFF 90 to 110 Ω


Text in Illustration
*a Component without harness connected
(Airbag Cut Off Switch Cylinder Sub-assembly)



OK

7.CHECK AIRBAG ECU ASSEMBLY

NG

REPLACE AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

7.CHECK AIRBAG ECU ASSEMBLY
a.
C238328E03
0.667,0.802 0.854,0.958 0.188,0.156 10 false *1 1.875,0.802 2.063,0.958 0.188,0.156 10 false A 1.719,0.802 1.906,0.958 0.188,0.156 10 false B 1.25,0.802 1.438,0.958 0.188,0.156 10 false C 1.083,0.802 1.271,0.958 0.188,0.156 10 false D 2.333,1.115 2.521,1.271 0.188,0.156 10 false *2

Connect the connectors to the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1651/33 is not output.


HINT:

Codes other than DTC B1651/33 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly



OK

NG