Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617/84  Lost Communication with Front Airbag Sensor LH  B1618/84  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag ECU assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1617/84
B1618/84
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag ECU assembly



WIRING DIAGRAM

C372338E02
1.844,0.781 2.177,1 0.333,0.219 10 false 2 3.448,0.896 3.896,1.125 0.448,0.229 10 false AL6 1.854,1.948 2.188,2.167 0.333,0.219 10 false 1 5.115,0.781 5.448,1 0.333,0.219 10 false 30 5.115,1.948 5.448,2.167 0.333,0.219 10 false 28 0.552,2.927 0.885,3.146 0.333,0.219 10 false A8 0.552,3.104 2.156,3.354 1.604,0.25 10 false Front Airbag Sensor LH 5.365,2.927 5.698,3.146 0.333,0.219 10 false L16 5.354,3.094 6.896,3.406 1.542,0.313 10 false Airbag ECU Assembly 1.448,0.885 1.896,1.125 0.448,0.24 10 false +SL 1.5,2.063 1.948,2.302 0.448,0.24 10 false -SL 5.385,0.885 5.833,1.125 0.448,0.24 10 false +SL 5.396,2.052 5.844,2.292 0.448,0.24 10 false -SL 3.458,2.073 3.906,2.302 0.448,0.229 10 false AL6 3.531,1.865 3.865,2.083 0.333,0.219 10 false 2 3.521,0.677 3.854,0.896 0.333,0.219 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)
a.
U191070E01
0.709,2.093 0.818,2.246 0.109,0.153 10 F 1.017,2.093 1.138,2.246 0.121,0.153 10 E 1.464,2.093 1.585,2.246 0.121,0.153 10 D 1.625,2.093 1.746,2.246 0.121,0.153 10 C 2.069,2.093 2.190,2.246 0.121,0.153 10 B 2.39,2.093 2.511,2.246 0.121,0.153 10 A 0.385,2.093 0.570,2.265 0.186,0.172 10 *1 2.78,2.39 2.935,2.547 0.156,0.157 10 *2 0.879,0.256 1.074,0.421 0.195,0.165 10 *a 0.373,3.192 0.540,3.346 0.167,0.155 10 *b 1.016,0.664 1.338,0.822 0.322,0.158 10 L16 1.745,1.033 2.006,1.191 0.260,0.158 10 -SL 2.697,1.033 2.991,1.191 0.294,0.158 10 +SL 0.569,3.636 0.769,3.793 0.200,0.158 10 A8 2.227,0.921 2.047,1.129 false 2.461,0.913 2.668,1.138 false 0.853,4.167 1.095,4.325 0.242,0.158 10 -SL 1.539,4.167 1.825,4.325 0.286,0.158 10 +SL 1.25,3.733 1.038,4.144 false 1.499,3.733 1.696,4.153 false 2.345,1.171 2.345,1.375 false 2.26,1.387 2.416,1.544 0.156,0.157 10 *3

Connect the connectors that link the engine room main wire and instrument panel wire.


b.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A8-2 (+SL) - A8-1 (-SL) Always Below 1 Ω


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

NG

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)
a.
U191065E01
0.662,0.599 0.771,0.751 0.109,0.153 10 F 0.971,0.599 1.092,0.751 0.121,0.153 10 E 1.414,0.599 1.535,0.751 0.121,0.153 10 D 1.568,0.599 1.689,0.751 0.121,0.153 10 C 2.023,0.599 2.144,0.751 0.121,0.153 10 B 2.339,0.599 2.460,0.751 0.121,0.153 10 A 0.358,0.599 0.542,0.777 0.184,0.178 10 *1 2.762,0.878 2.930,1.060 0.167,0.181 10 *2 0.166,1.69 0.373,1.853 0.207,0.163 10 *a 0.444,2.213 0.635,2.371 0.191,0.158 10 A8 0.844,2.812 1.104,2.970 0.260,0.158 10 -SL 1.479,2.812 1.800,2.970 0.321,0.158 10 +SL 1.225,2.358 1.036,2.782 false 1.458,2.367 1.654,2.799 false

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A8-2 (+SL) - A8-1 (-SL) Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)
a.
U191065E01
0.662,0.599 0.771,0.751 0.109,0.153 10 F 0.971,0.599 1.092,0.751 0.121,0.153 10 E 1.414,0.599 1.535,0.751 0.121,0.153 10 D 1.568,0.599 1.689,0.751 0.121,0.153 10 C 2.023,0.599 2.144,0.751 0.121,0.153 10 B 2.339,0.599 2.460,0.751 0.121,0.153 10 A 0.358,0.599 0.542,0.777 0.184,0.178 10 *1 2.762,0.878 2.930,1.060 0.167,0.181 10 *2 0.166,1.69 0.373,1.853 0.207,0.163 10 *a 0.444,2.213 0.635,2.371 0.191,0.158 10 A8 0.844,2.812 1.104,2.970 0.260,0.158 10 -SL 1.479,2.812 1.800,2.970 0.321,0.158 10 +SL 1.225,2.358 1.036,2.782 false 1.458,2.367 1.654,2.799 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A8-2 (+SL) - Body ground Power switch on (IG) Below 1 V
A8-1 (-SL) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)
a.
U191065E01
0.662,0.599 0.771,0.751 0.109,0.153 10 F 0.971,0.599 1.092,0.751 0.121,0.153 10 E 1.414,0.599 1.535,0.751 0.121,0.153 10 D 1.568,0.599 1.689,0.751 0.121,0.153 10 C 2.023,0.599 2.144,0.751 0.121,0.153 10 B 2.339,0.599 2.460,0.751 0.121,0.153 10 A 0.358,0.599 0.542,0.777 0.184,0.178 10 *1 2.762,0.878 2.930,1.060 0.167,0.181 10 *2 0.166,1.69 0.373,1.853 0.207,0.163 10 *a 0.444,2.213 0.635,2.371 0.191,0.158 10 A8 0.844,2.812 1.104,2.970 0.260,0.158 10 -SL 1.479,2.812 1.800,2.970 0.321,0.158 10 +SL 1.225,2.358 1.036,2.782 false 1.458,2.367 1.654,2.799 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A8-2 (+SL) - Body ground Always 1 MΩ or higher
A8-1 (-SL) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

6.CHECK FRONT AIRBAG SENSOR LH

NG

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR LH
a.
C238211E01
2.195,0.812 2.316,0.967 0.121,0.156 10 A 2.036,0.812 2.157,0.967 0.121,0.156 10 B 1.581,0.812 1.703,0.967 0.121,0.156 10 C 1.425,0.812 1.546,0.967 0.121,0.156 10 D 0.98,0.812 1.101,0.967 0.121,0.156 10 E 0.829,0.812 0.950,0.967 0.121,0.156 10 F 0.514,0.812 0.698,0.989 0.184,0.178 10 *1 2.585,1.092 2.752,1.238 0.167,0.146 10 *2

Connect the connector to the airbag ECU assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. A
DTC B1617/84 or B1618/84 is output. B
DTC B1612/83 or B1613/83 is output. C


HINT:

Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84, may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the front airbag sensor LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U191071E02
2.271,0.927 2.083,1.135 true 2.5,0.927 2.698,1.146 true 1.969,3.74 1.729,4.188 false 2.177,3.74 2.479,4.177 false 1.177,2.281 1.177,2.49 false 1.958,2.281 1.958,2.49 false 2.375,1.167 2.375,1.354 false 0.594,2.115 0.698,2.271 0.104,0.156 10 false F 0.906,2.115 1.031,2.271 0.125,0.156 10 false E 1.354,2.115 1.479,2.271 0.125,0.156 10 false D 1.667,2.115 1.792,2.271 0.125,0.156 10 false C 2.115,2.115 2.24,2.271 0.125,0.156 10 false B 2.427,2.115 2.552,2.271 0.125,0.156 10 false A 1.083,0.646 1.375,0.802 0.292,0.156 10 false L16 1.781,1.052 2.042,1.208 0.26,0.156 10 false -SL 2.729,1.052 3.052,1.208 0.323,0.156 10 false +SL 1.24,3.698 1.563,3.854 0.323,0.156 10 false AL6 2.354,4.208 2.635,4.365 0.281,0.156 10 false +SL 1.604,4.208 1.844,4.365 0.24,0.156 10 false -SL 2.771,2.396 2.969,2.552 0.198,0.156 10 false *2 1.094,2.5 1.292,2.656 0.198,0.156 10 false *3 0.313,2.094 0.51,2.25 0.198,0.156 10 false *1 0.938,0.281 1.135,0.438 0.198,0.156 10 false *a 1.031,3.219 1.229,3.375 0.198,0.156 10 false *b 1.865,2.5 2.063,2.656 0.198,0.156 10 false *4 2.292,1.365 2.448,1.521 0.156,0.156 10 false *5

Disconnect the instrument panel wire connector from the engine room main wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AL6-1 (+SL) - AL6-2 (-SL) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U191068E01
0.608,0.544 0.718,0.696 0.109,0.153 10 F 0.911,0.544 1.032,0.696 0.121,0.153 10 E 1.364,0.544 1.485,0.696 0.121,0.153 10 D 1.669,0.544 1.789,0.696 0.121,0.153 10 C 2.131,0.544 2.252,0.696 0.121,0.153 10 B 2.442,0.544 2.562,0.696 0.121,0.153 10 A 0.281,0.544 0.456,0.719 0.176,0.175 10 *1 2.813,0.813 2.982,0.987 0.169,0.174 10 *2 1.622,0.068 1.783,0.221 0.160,0.152 10 *4 1.109,0.968 1.304,1.120 0.195,0.152 10 *3 0.734,1.605 0.928,1.789 0.194,0.183 10 *a 1.005,2.156 1.333,2.314 0.327,0.158 10 AL6 1.455,2.681 1.720,2.838 0.265,0.158 10 -SL 2.25,2.681 2.549,2.838 0.299,0.158 10 +SL 1.939,2.242 1.64,2.663 false 2.092,2.238 2.428,2.663 false 1.196,0.695 1.196,0.954 false 1.955,0.554 1.955,0.154 1.955,0.154 1.804,0.154 false

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AL6-1 (+SL) - AL6-2 (-SL) Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U191068E01
0.608,0.544 0.718,0.696 0.109,0.153 10 F 0.911,0.544 1.032,0.696 0.121,0.153 10 E 1.364,0.544 1.485,0.696 0.121,0.153 10 D 1.669,0.544 1.789,0.696 0.121,0.153 10 C 2.131,0.544 2.252,0.696 0.121,0.153 10 B 2.442,0.544 2.562,0.696 0.121,0.153 10 A 0.281,0.544 0.456,0.719 0.176,0.175 10 *1 2.813,0.813 2.982,0.987 0.169,0.174 10 *2 1.622,0.068 1.783,0.221 0.160,0.152 10 *4 1.109,0.968 1.304,1.120 0.195,0.152 10 *3 0.734,1.605 0.928,1.789 0.194,0.183 10 *a 1.005,2.156 1.333,2.314 0.327,0.158 10 AL6 1.455,2.681 1.720,2.838 0.265,0.158 10 -SL 2.25,2.681 2.549,2.838 0.299,0.158 10 +SL 1.939,2.242 1.64,2.663 false 2.092,2.238 2.428,2.663 false 1.196,0.695 1.196,0.954 false 1.955,0.554 1.955,0.154 1.955,0.154 1.804,0.154 false

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
AL6-1 (+SL) - Body ground Power switch on (IG) Below 1 V
AL6-2 (-SL) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U191068E01
0.608,0.544 0.718,0.696 0.109,0.153 10 F 0.911,0.544 1.032,0.696 0.121,0.153 10 E 1.364,0.544 1.485,0.696 0.121,0.153 10 D 1.669,0.544 1.789,0.696 0.121,0.153 10 C 2.131,0.544 2.252,0.696 0.121,0.153 10 B 2.442,0.544 2.562,0.696 0.121,0.153 10 A 0.281,0.544 0.456,0.719 0.176,0.175 10 *1 2.813,0.813 2.982,0.987 0.169,0.174 10 *2 1.622,0.068 1.783,0.221 0.160,0.152 10 *4 1.109,0.968 1.304,1.120 0.195,0.152 10 *3 0.734,1.605 0.928,1.789 0.194,0.183 10 *a 1.005,2.156 1.333,2.314 0.327,0.158 10 AL6 1.455,2.681 1.720,2.838 0.265,0.158 10 -SL 2.25,2.681 2.549,2.838 0.299,0.158 10 +SL 1.939,2.242 1.64,2.663 false 2.092,2.238 2.428,2.663 false 1.196,0.695 1.196,0.954 false 1.955,0.554 1.955,0.154 1.955,0.154 1.804,0.154 false

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AL6-1 (+SL) - Body ground Always 1 MΩ or higher
AL6-2 (-SL) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE