Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1627/82  Lost communication with Side Airbag Sensor LH  B1628/82  Side Airbag Sensor Assembly LH Initialization Incomplete  B1637/82  Lost Communication with Rear Airbag Sensor LH  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH, curtain shield airbag assembly LH and front seat outer belt assembly LH) is composed of the airbag ECU assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

The side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbag and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1627/82
B1628/82
B1637/82
B1638/82
B1647/82
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Side airbag sensor assembly LH

·

Side No. 2 airbag sensor assembly LH

·

Airbag ECU assembly



WIRING DIAGRAM

C239250E99
0.521,4.698 0.74,4.844 0.219,0.146 10 false R9 0.521,4.865 1.75,5.198 1.229,0.333 10 false Side Airbag Sensor Assembly LH 3.01,4.865 4.354,5.281 1.344,0.417 10 false Side No. 2 Airbag Sensor Assembly LH 3.01,4.698 3.292,4.844 0.281,0.146 10 false R34 5.521,4.865 7.115,5.063 1.594,0.198 10 false Airbag ECU Assembly 5.521,4.698 5.75,4.844 0.229,0.146 10 false R1 1.135,0.896 1.531,1.052 0.396,0.156 10 false BBL+ 1.583,0.792 1.688,0.948 0.104,0.156 10 false 4 1.167,1.792 1.531,1.948 0.365,0.156 10 false BBL- 5.563,0.896 5.958,1.052 0.396,0.156 10 false BBL+ 5.375,0.792 5.552,0.948 0.177,0.156 10 false 8 5.333,1.698 5.51,1.854 0.177,0.156 10 false 15 5.563,1.792 5.958,1.948 0.396,0.156 10 false BBL- 1.583,1.698 1.688,1.854 0.104,0.156 10 false 3 1.135,3.042 1.531,3.198 0.396,0.156 10 false BCL+ 1.583,2.948 1.688,3.104 0.104,0.156 10 false 1 2.927,3.833 3.031,3.99 0.104,0.156 10 false 1 1.156,3.938 1.531,4.094 0.375,0.156 10 false BCL- 3.073,3.042 3.469,3.198 0.396,0.156 10 false BCL+ 3.073,3.938 3.469,4.094 0.396,0.156 10 false BCL- 1.583,3.833 1.688,3.99 0.104,0.156 10 false 2 2.927,2.948 3.031,3.104 0.104,0.156 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1647 or 82 is output. A
Current DTC B1628 is output. B
Current DTC B1637 or B1638 is output. C
Current DTC B1627 is output. D
Current DTCs B1627, B1628, B1637, B1638, B1647 and 82 are not output. E


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

·

Codes other than current DTCs B1627, B1628, B1637, B1638, B1647 and 82 may be output at this time, but they are not related to this check.





A

2.CHECK CONNECTORS

B

13.CHECK HISTORY DTC

C

20.CHECK CONNECTORS

D

27.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

E

2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

3.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (OPEN)
a.
U191077E02
1.521,3.75 1.198,4.135 true 1.656,3.75 1.979,4.135 true 1.531,2.25 1.531,1.771 1.531,1.771 1.365,1.771 true 2.01,1.125 2.01,1.323 true 1.927,0.677 1.479,1.156 true 2.167,0.885 2.51,1.146 true 0.948,2.26 1.073,2.417 0.125,0.156 10 false D 1.26,2.26 1.385,2.417 0.125,0.156 10 false C 1.719,2.26 1.844,2.417 0.125,0.156 10 false B 2.021,2.26 2.146,2.417 0.125,0.156 10 false A 0.625,2.24 0.813,2.427 0.188,0.188 10 false *1 2.438,2.24 2.646,2.438 0.208,0.198 10 false *2 0.771,0.302 0.938,0.49 0.167,0.188 10 false *a 0.302,3.156 0.479,3.354 0.177,0.198 10 false *b 1.302,1.167 1.677,1.323 0.375,0.156 10 false BBL+ 2.385,1.167 2.719,1.323 0.333,0.156 10 false BBL- 1.115,0.625 1.323,0.781 0.208,0.156 10 false R1 0.51,3.625 0.729,3.781 0.219,0.156 10 false R9 1.792,4.146 2.156,4.302 0.365,0.156 10 false BBL+ 0.969,4.146 1.313,4.302 0.344,0.156 10 false BBL- 1.177,1.688 1.354,1.885 0.177,0.198 10 false *3 1.927,1.333 2.083,1.531 0.156,0.198 10 false *4

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-4 (BBL+) - R9-3 (BBL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
a.
U191078E01
0.97,0.712 1.091,0.865 0.121,0.153 10 D 1.286,0.712 1.406,0.865 0.121,0.153 10 C 1.739,0.712 1.860,0.865 0.121,0.153 10 B 2.056,0.712 2.177,0.865 0.121,0.153 10 A 0.668,0.712 0.845,0.925 0.176,0.213 10 *1 2.44,0.712 2.639,0.892 0.198,0.180 10 *2 0.345,1.827 0.552,2.007 0.208,0.180 10 *a 0.515,2.318 0.744,2.475 0.229,0.158 10 R9 1.821,2.83 2.199,2.987 0.378,0.158 10 BBL+ 0.96,2.83 1.302,2.987 0.342,0.158 10 BBL- 1.539,2.451 1.194,2.797 false 1.68,2.451 2.026,2.797 false 1.766,0.245 1.988,0.392 0.222,0.147 10 *3 1.569,0.73 1.569,0.329 1.569,0.329 1.722,0.329 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-4 (BBL+) - R9-3 (BBL-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

5.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO B+)
a.
U191078E01
0.97,0.712 1.091,0.865 0.121,0.153 10 D 1.286,0.712 1.406,0.865 0.121,0.153 10 C 1.739,0.712 1.860,0.865 0.121,0.153 10 B 2.056,0.712 2.177,0.865 0.121,0.153 10 A 0.668,0.712 0.845,0.925 0.176,0.213 10 *1 2.44,0.712 2.639,0.892 0.198,0.180 10 *2 0.345,1.827 0.552,2.007 0.208,0.180 10 *a 0.515,2.318 0.744,2.475 0.229,0.158 10 R9 1.821,2.83 2.199,2.987 0.378,0.158 10 BBL+ 0.96,2.83 1.302,2.987 0.342,0.158 10 BBL- 1.539,2.451 1.194,2.797 false 1.68,2.451 2.026,2.797 false 1.766,0.245 1.988,0.392 0.222,0.147 10 *3 1.569,0.73 1.569,0.329 1.569,0.329 1.722,0.329 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R9-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
R9-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

6.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U191078E01
0.97,0.712 1.091,0.865 0.121,0.153 10 D 1.286,0.712 1.406,0.865 0.121,0.153 10 C 1.739,0.712 1.860,0.865 0.121,0.153 10 B 2.056,0.712 2.177,0.865 0.121,0.153 10 A 0.668,0.712 0.845,0.925 0.176,0.213 10 *1 2.44,0.712 2.639,0.892 0.198,0.180 10 *2 0.345,1.827 0.552,2.007 0.208,0.180 10 *a 0.515,2.318 0.744,2.475 0.229,0.158 10 R9 1.821,2.83 2.199,2.987 0.378,0.158 10 BBL+ 0.96,2.83 1.302,2.987 0.342,0.158 10 BBL- 1.539,2.451 1.194,2.797 false 1.68,2.451 2.026,2.797 false 1.766,0.245 1.988,0.392 0.222,0.147 10 *3 1.569,0.73 1.569,0.329 1.569,0.329 1.722,0.329 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-4 (BBL+) - Body ground Always 1 MΩ or higher
R9-3 (BBL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

7.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (OPEN)
a.
U191140E02
1.646,3.708 1.281,4.063 true 1.802,3.708 2.177,4.063 true 1.833,0.667 1.573,1.01 true 1.948,0.667 2.208,1.01 true 1.729,4.125 1.729,4.302 true 1.708,2.271 1.708,1.75 1.708,1.75 1.49,1.75 false 1.052,2.25 1.177,2.406 0.125,0.156 10 false D 1.354,2.25 1.479,2.406 0.125,0.156 10 false C 1.948,2.25 2.073,2.406 0.125,0.156 10 false B 2.271,2.25 2.396,2.406 0.125,0.156 10 false A 0.667,2.229 0.813,2.385 0.146,0.156 10 false *1 2.573,2.229 2.74,2.406 0.167,0.177 10 false *2 1.052,4.094 1.417,4.25 0.365,0.156 10 false BCL- 1.958,4.094 2.365,4.25 0.406,0.156 10 false BCL+ 0.615,3.635 0.917,3.792 0.302,0.156 10 false R34 1.073,0.583 1.292,0.74 0.219,0.156 10 false R9 2.01,1.021 2.385,1.177 0.375,0.156 10 false BCL- 1.313,1.021 1.719,1.177 0.406,0.156 10 false BCL+ 1.313,1.677 1.469,1.823 0.156,0.146 10 false *3 0.813,0.146 1.01,0.354 0.198,0.208 10 false *a 0.427,3.156 0.625,3.365 0.198,0.208 10 false *b 1.646,4.302 1.792,4.458 0.146,0.156 10 false *4

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-1 (BCL+) - R9-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)



OK

8.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (SHORT)
a.
U191076E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.211,2.317 1.433,2.474 0.222,0.158 10 R9 2.278,2.865 2.666,3.023 0.387,0.158 10 BCL- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-1 (BCL+) - R9-2 (BCL-) Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

9.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE (SHORT TO B+)
a.
U191076E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.211,2.317 1.433,2.474 0.222,0.158 10 R9 2.278,2.865 2.666,3.023 0.387,0.158 10 BCL- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R9-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
R9-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

10.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U191076E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.211,2.317 1.433,2.474 0.222,0.158 10 R9 2.278,2.865 2.666,3.023 0.387,0.158 10 BCL- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-1 (BCL+) - Body ground Always 1 MΩ or higher
R9-2 (BCL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224E01
0.794,0.965 0.944,1.152 0.150,0.187 10 *1 2.312,0.965 2.521,1.152 0.209,0.187 10 *2 1.872,0.965 2.001,1.152 0.129,0.187 10 A 1.71,0.965 1.839,1.152 0.129,0.187 10 B 1.261,0.965 1.389,1.152 0.129,0.187 10 C 1.108,0.965 1.236,1.152 0.129,0.187 10 D

Connect the connectors to the side No. 2 airbag sensor assembly LH and airbag ECU assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1647 or 82 is output. A
DTC B1642 or 81 is output. B
DTCs B1642, B1647, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly



A

12.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C

12.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223E01
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1642, B1647, 81 and 82 are not output. A
DTC B1647 or 82 is output. B
DTC B1642 or 81 is output. C


HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

13.CHECK HISTORY DTC
a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTC B1627 is not output. A
History DTC B1627 is output. B


HINT:

Codes other than history DTC B1627 may be output at this time, but they are not related to this check.




A

14.CHECK CONNECTORS

B

27.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
14.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and side airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and side airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

15.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

15.CHECK FLOOR WIRE (OPEN)
a.
U191077E02
1.521,3.75 1.198,4.135 true 1.656,3.75 1.979,4.135 true 1.531,2.25 1.531,1.771 1.531,1.771 1.365,1.771 true 2.01,1.125 2.01,1.323 true 1.927,0.677 1.479,1.156 true 2.167,0.885 2.51,1.146 true 0.948,2.26 1.073,2.417 0.125,0.156 10 false D 1.26,2.26 1.385,2.417 0.125,0.156 10 false C 1.719,2.26 1.844,2.417 0.125,0.156 10 false B 2.021,2.26 2.146,2.417 0.125,0.156 10 false A 0.625,2.24 0.813,2.427 0.188,0.188 10 false *1 2.438,2.24 2.646,2.438 0.208,0.198 10 false *2 0.771,0.302 0.938,0.49 0.167,0.188 10 false *a 0.302,3.156 0.479,3.354 0.177,0.198 10 false *b 1.302,1.167 1.677,1.323 0.375,0.156 10 false BBL+ 2.385,1.167 2.719,1.323 0.333,0.156 10 false BBL- 1.115,0.625 1.323,0.781 0.208,0.156 10 false R1 0.51,3.625 0.729,3.781 0.219,0.156 10 false R9 1.792,4.146 2.156,4.302 0.365,0.156 10 false BBL+ 0.969,4.146 1.313,4.302 0.344,0.156 10 false BBL- 1.177,1.688 1.354,1.885 0.177,0.198 10 false *3 1.927,1.333 2.083,1.531 0.156,0.198 10 false *4

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-4 (BBL+) - R9-3 (BBL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

16.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

16.CHECK FLOOR WIRE (SHORT)
a.
U191078E01
0.97,0.712 1.091,0.865 0.121,0.153 10 D 1.286,0.712 1.406,0.865 0.121,0.153 10 C 1.739,0.712 1.860,0.865 0.121,0.153 10 B 2.056,0.712 2.177,0.865 0.121,0.153 10 A 0.668,0.712 0.845,0.925 0.176,0.213 10 *1 2.44,0.712 2.639,0.892 0.198,0.180 10 *2 0.345,1.827 0.552,2.007 0.208,0.180 10 *a 0.515,2.318 0.744,2.475 0.229,0.158 10 R9 1.821,2.83 2.199,2.987 0.378,0.158 10 BBL+ 0.96,2.83 1.302,2.987 0.342,0.158 10 BBL- 1.539,2.451 1.194,2.797 false 1.68,2.451 2.026,2.797 false 1.766,0.245 1.988,0.392 0.222,0.147 10 *3 1.569,0.73 1.569,0.329 1.569,0.329 1.722,0.329 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-4 (BBL+) - R9-3 (BBL-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

17.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

17.CHECK FLOOR WIRE (SHORT TO B+)
a.
U191078E01
0.97,0.712 1.091,0.865 0.121,0.153 10 D 1.286,0.712 1.406,0.865 0.121,0.153 10 C 1.739,0.712 1.860,0.865 0.121,0.153 10 B 2.056,0.712 2.177,0.865 0.121,0.153 10 A 0.668,0.712 0.845,0.925 0.176,0.213 10 *1 2.44,0.712 2.639,0.892 0.198,0.180 10 *2 0.345,1.827 0.552,2.007 0.208,0.180 10 *a 0.515,2.318 0.744,2.475 0.229,0.158 10 R9 1.821,2.83 2.199,2.987 0.378,0.158 10 BBL+ 0.96,2.83 1.302,2.987 0.342,0.158 10 BBL- 1.539,2.451 1.194,2.797 false 1.68,2.451 2.026,2.797 false 1.766,0.245 1.988,0.392 0.222,0.147 10 *3 1.569,0.73 1.569,0.329 1.569,0.329 1.722,0.329 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R9-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
R9-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

18.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

18.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U191078E01
0.97,0.712 1.091,0.865 0.121,0.153 10 D 1.286,0.712 1.406,0.865 0.121,0.153 10 C 1.739,0.712 1.860,0.865 0.121,0.153 10 B 2.056,0.712 2.177,0.865 0.121,0.153 10 A 0.668,0.712 0.845,0.925 0.176,0.213 10 *1 2.44,0.712 2.639,0.892 0.198,0.180 10 *2 0.345,1.827 0.552,2.007 0.208,0.180 10 *a 0.515,2.318 0.744,2.475 0.229,0.158 10 R9 1.821,2.83 2.199,2.987 0.378,0.158 10 BBL+ 0.96,2.83 1.302,2.987 0.342,0.158 10 BBL- 1.539,2.451 1.194,2.797 false 1.68,2.451 2.026,2.797 false 1.766,0.245 1.988,0.392 0.222,0.147 10 *3 1.569,0.73 1.569,0.329 1.569,0.329 1.722,0.329 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-4 (BBL+) - Body ground Always 1 MΩ or higher
R9-3 (BBL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224E01
0.794,0.965 0.944,1.152 0.150,0.187 10 *1 2.312,0.965 2.521,1.152 0.209,0.187 10 *2 1.872,0.965 2.001,1.152 0.129,0.187 10 A 1.71,0.965 1.839,1.152 0.129,0.187 10 B 1.261,0.965 1.389,1.152 0.129,0.187 10 C 1.108,0.965 1.236,1.152 0.129,0.187 10 D

Connect the connector to the airbag ECU assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1623 and B1628 are not output. A
DTC B1628 is output. B
DTC B1623 is output. C


HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly



A

B

C

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

20.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

21.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (OPEN)
a.
U191140E02
1.646,3.708 1.281,4.063 true 1.802,3.708 2.177,4.063 true 1.833,0.667 1.573,1.01 true 1.948,0.667 2.208,1.01 true 1.729,4.125 1.729,4.302 true 1.708,2.271 1.708,1.75 1.708,1.75 1.49,1.75 false 1.052,2.25 1.177,2.406 0.125,0.156 10 false D 1.354,2.25 1.479,2.406 0.125,0.156 10 false C 1.948,2.25 2.073,2.406 0.125,0.156 10 false B 2.271,2.25 2.396,2.406 0.125,0.156 10 false A 0.667,2.229 0.813,2.385 0.146,0.156 10 false *1 2.573,2.229 2.74,2.406 0.167,0.177 10 false *2 1.052,4.094 1.417,4.25 0.365,0.156 10 false BCL- 1.958,4.094 2.365,4.25 0.406,0.156 10 false BCL+ 0.615,3.635 0.917,3.792 0.302,0.156 10 false R34 1.073,0.583 1.292,0.74 0.219,0.156 10 false R9 2.01,1.021 2.385,1.177 0.375,0.156 10 false BCL- 1.313,1.021 1.719,1.177 0.406,0.156 10 false BCL+ 1.313,1.677 1.469,1.823 0.156,0.146 10 false *3 0.813,0.146 1.01,0.354 0.198,0.208 10 false *a 0.427,3.156 0.625,3.365 0.198,0.208 10 false *b 1.646,4.302 1.792,4.458 0.146,0.156 10 false *4

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-1 (BCL+) - R9-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)



OK

22.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

22.CHECK FLOOR WIRE (SHORT)
a.
U191076E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.211,2.317 1.433,2.474 0.222,0.158 10 R9 2.278,2.865 2.666,3.023 0.387,0.158 10 BCL- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-1 (BCL+) - R9-2 (BCL-) Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

23.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

23.CHECK FLOOR WIRE (SHORT TO B+)
a.
U191076E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.211,2.317 1.433,2.474 0.222,0.158 10 R9 2.278,2.865 2.666,3.023 0.387,0.158 10 BCL- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R9-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
R9-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

24.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

24.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U191076E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.211,2.317 1.433,2.474 0.222,0.158 10 R9 2.278,2.865 2.666,3.023 0.387,0.158 10 BCL- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R9-1 (BCL+) - Body ground Always 1 MΩ or higher
R9-2 (BCL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

25.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

25.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224E01
0.794,0.965 0.944,1.152 0.150,0.187 10 *1 2.312,0.965 2.521,1.152 0.209,0.187 10 *2 1.872,0.965 2.001,1.152 0.129,0.187 10 A 1.71,0.965 1.839,1.152 0.129,0.187 10 B 1.261,0.965 1.389,1.152 0.129,0.187 10 C 1.108,0.965 1.236,1.152 0.129,0.187 10 D

Connect the connector to the side No. 2 airbag sensor assembly LH.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1637 or B1638 is output. A
DTC B1632 or B1633 is output. B
DTCs B1632, B1633, B1637 and B1638 are not output. C


HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly



A

26.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C

26.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223E01
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1632, B1633, B1637 and B1638 are not output. A
DTC B1637 or B1638 is output. B
DTC B1632 or B1633 is output. C


HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

27.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224E01
0.794,0.965 0.944,1.152 0.150,0.187 10 *1 2.312,0.965 2.521,1.152 0.209,0.187 10 *2 1.872,0.965 2.001,1.152 0.129,0.187 10 A 1.71,0.965 1.839,1.152 0.129,0.187 10 B 1.261,0.965 1.389,1.152 0.129,0.187 10 C 1.108,0.965 1.236,1.152 0.129,0.187 10 D

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1622 and B1627 are not output. A
DTC B1627 is output. B
DTC B1622 is output. C


HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly



A

B

C

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH