Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301800 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 84307 1.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

a.

Visually check for defects with the spiral cable with sensor sub-assembly removed from the vehicle.

i.

The defects are as follows:

·

Scratches on the spiral cable with sensor sub-assembly

·

Small cracks on the spiral cable with sensor sub-assembly

·

Dents on the spiral cable with sensor sub-assembly

·

Chips on the spiral cable with sensor sub-assembly

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable with sensor sub-assembly with a new one.



b.

Check the spiral cable with sensor sub-assembly.

C370355E02
4.354,0.094 4.771,0.344 0.417,0.25 4.229,1.594 4.646,1.844 0.417,0.25 4.927,0.094 5.344,0.344 0.417,0.25 5.323,1.802 5.74,2.031 0.417,0.229 1.083,0.125 1.5,0.375 0.417,0.25 0.24,0.115 0.552,0.313 0.313,0.198 10 false *a 4.49,0.135 4.802,0.333 0.313,0.198 10 false z9 4.313,1.635 4.625,1.833 0.313,0.198 10 false L52 5.031,0.135 5.344,0.333 0.313,0.198 10 false z10 5.406,1.833 5.719,2.031 0.313,0.198 10 false L53 1.219,0.167 1.531,0.365 0.313,0.198 10 false z8

Text in Illustration
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)

NOTICE:

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.


i.

Set the spiral cable with sensor sub-assembly to the center position.


ii.

Measure the resistance between each terminal of the spiral cable with sensor sub-assembly according to the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-1 (CCS) - z10-3 Always 3 Ω or less
L52-2 (ECC) - z10-4 Always 3 Ω or less
L52-2 (ECC) - z9-6 Always 3 Ω or less
L52-3 (DISP/TX1) - z9-7 Always 3 Ω or less
L52-4 (EAU) - z9-8 Always 3 Ω or less
L52-5 (AU2) - z9-9 Always 3 Ω or less
L52-6 (AU1) - z9-10 Always 3 Ω or less
L52-7 (R/N) - z10-1 Always 3 Ω or less
L52-8 (HO) - z9-1 Always 3 Ω or less
L52-9 (TRIP/IG) - z9-2 Always 3 Ω or less
L52-10 (AC1) - z9-3 Always 3 Ω or less
L52-11 (DIST) - z9-4 Always 3 Ω or less
L52-12 (IL+2) - z9-5 Always 3 Ω or less
L53-1 (D+) - z8-2 Always Below 1 Ω
L53-2 (D-) - z8-1 Always Below 1 Ω



iii.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable with sensor sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-1 (CCS) - z10-3 Always 3 Ω or less
L52-2 (ECC) - z10-4 Always 3 Ω or less
L52-2 (ECC) - z9-6 Always 3 Ω or less
L52-3 (DISP/TX1) - z9-7 Always 3 Ω or less
L52-4 (EAU) - z9-8 Always 3 Ω or less
L52-5 (AU2) - z9-9 Always 3 Ω or less
L52-6 (AU1) - z9-10 Always 3 Ω or less
L52-7 (R/N) - z10-1 Always 3 Ω or less
L52-8 (HO) - z9-1 Always 3 Ω or less
L52-9 (TRIP/IG) - z9-2 Always 3 Ω or less
L52-10 (AC1) - z9-3 Always 3 Ω or less
L52-11 (DIST) - z9-4 Always 3 Ω or less
L52-12 (IL+2) - z9-5 Always 3 Ω or less
L53-1 (D+) - z8-2 Always Below 1 Ω
L53-2 (D-) - z8-1 Always Below 1 Ω



iv.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-1 (CCS) - z10-3 Always 3 Ω or less
L52-2 (ECC) - z10-4 Always 3 Ω or less
L52-2 (ECC) - z9-6 Always 3 Ω or less
L52-3 (DISP/TX1) - z9-7 Always 3 Ω or less
L52-4 (EAU) - z9-8 Always 3 Ω or less
L52-5 (AU2) - z9-9 Always 3 Ω or less
L52-6 (AU1) - z9-10 Always 3 Ω or less
L52-7 (R/N) - z10-1 Always 3 Ω or less
L52-8 (HO) - z9-1 Always 3 Ω or less
L52-9 (TRIP/IG) - z9-2 Always 3 Ω or less
L52-10 (AC1) - z9-3 Always 3 Ω or less
L52-11 (DIST) - z9-4 Always 3 Ω or less
L52-12 (IL+2) - z9-5 Always 3 Ω or less
L53-1 (D+) - z8-2 Always Below 1 Ω
L53-2 (D-) - z8-1 Always Below 1 Ω


If the result is not as specified, replace the spiral cable with sensor sub-assembly.