Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR › from 2016.05
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301808 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 64910J 2.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 3.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 62332A 7.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the deck trim side panel assembly.


Hide 58460D 9.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

Hide 64713F 10.REMOVE FRONT DECK SIDE TRIM COVER

Hide 73370C 11.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

Hide 73350 12.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY (for Lower Side)

Hide 64740C 14.REMOVE DECK TRIM SIDE PANEL ASSEMBLY

Hide 89860B 15.REMOVE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the side No. 2 airbag sensor assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

B282170E02
1.448,1.698 1.5,1.698 1.5,1.698 1.656,1.854 true 1.885,2.104 1.969,2.177 1.969,2.177 1.969,2.354 false 3.844,2.083 3.927,2.167 3.927,2.167 3.927,2.333 false 3.406,1.719 3.458,1.719 3.458,1.719 3.615,1.875 true 1.302,1.813 1.365,1.813 1.365,1.813 1.542,1.99 true 3.25,1.823 3.313,1.823 3.313,1.823 3.49,2 true 1.292,1.625 1.448,1.771 0.156,0.146 10 false *1 1.938,2.365 2.094,2.51 0.156,0.146 10 false *2 1.594,2.396 1.75,2.542 0.156,0.146 10 false *a 1.729,1.573 1.885,1.719 0.156,0.146 10 false *b 3.25,1.646 3.406,1.792 0.156,0.146 10 false *1 3.865,2.354 4.021,2.5 0.156,0.146 10 false *2 3.5,2.417 3.656,2.563 0.156,0.146 10 false *a 3.615,1.594 3.771,1.74 0.156,0.146 10 false *b 1.073,1.729 1.292,1.906 0.219,0.177 10 false (A) 3.021,1.74 3.24,1.917 0.219,0.177 10 false (A)

Text in Illustration
*1 White Housing Lock *2 Yellow CPA
*a Slide *b Push


ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting.




d.

Remove the bolt and side No. 2 airbag sensor assembly from the vehicle body.

NOTICE:

Loosen the bolt while holding the side No. 2 airbag sensor assembly because the side No. 2 airbag sensor assembly pin (stopper) is easily damaged.



e.

After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B442007