Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  TERMINALS OF ECU  


CHECK SEAT BELT CONTROL ECU


U191350E02
4.313,0.156 4.49,0.333 0.177,0.177 10 false L3 3.083,0.146 3.26,0.323 0.177,0.177 10 false L2

a.

Disconnect the seat belt control ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L2-7 (+B) - Body ground P - Body ground Auxiliary battery voltage Power switch off 11 to 14 V
L2-8 (PGND) - Body ground W-B - Body ground Body ground Always Below 1 Ω
L3-8 (IG1) - Body ground W - Body ground Seat belt control ECU power supply Power switch on (IG) 11 to 14 V
Power switch off Below 1 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L2-2 (MOR+) - L2-1 (MOR-) LG - L Seat belt motor RH power supply Power switch on (IG) 4.0 to 8.5 V
Power switch off Below 1 V
L2-3 (MOL+) - L2-4 (MOL-) B - W Seat belt motor LH power supply Power switch on (IG) 4.0 to 8.5 V
Power switch off Below 1 V

If the result is not as specified, the ECU may be malfunctioning.



CHECK DRIVING SUPPORT ECU ASSEMBLY


U155118E03
3.479,0.385 3.729,0.563 0.25,0.177 10 false L60

a.

Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L60-5 (PBSW) - Body ground L - Body ground Pre-crash brake cancel switch Pre-crash brake cancel switch assembly on Below 1 Ω
Pre-crash brake cancel switch assembly off 10 kΩ or higher
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control main switch signal Power switch on (IG) 1 MΩ or higher
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control main switch signal Power switch on (IG),
CANCEL switch on
1509 to 1571 Ω
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control main switch signal Power switch on (IG),
-/SET switch on
617 to 643 Ω
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control main switch signal Power switch on (IG),
+/RES switch on
235 to 245 Ω
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control main switch signal Power switch on (IG),
Main switch on
Below 2.5 Ω
L60-25 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
L60-7 (MODE) - Body ground R - Body ground MODE signal Power switch on (IG)
MODE switch off
11 to 14 V
Power switch on (IG)
MODE switch on
Below 2 V
L60-16 (LRDD) - Body ground V - Body ground Driving support ECU assembly communication signal Power switch on (IG) Pulse generation
(See waveform 2)
L60-17 (CA2L) - L60-25 (GND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
L60-38 (LRRD) - Body ground L - Body ground Driving support ECU assembly communication signal Power switch on (IG) Pulse generation
(See waveform 3)
L60-39 (CA2H) - L60-25 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 4)


e.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Driving Support ECU Assembly Terminal Name Between CA2L and GND
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




f.
E228689E01
2.998,1.218 3.324,1.393 0.326,0.174 10 GND

Waveform 2

Item Content
Driving Support ECU Assembly Terminal Name Between LRDD and GND
Tester Range 2 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)


g.
E228690E01
2.997,1.218 3.323,1.393 0.327,0.174 10 GND

Waveform 3

Item Content
Driving Support ECU Assembly Terminal Name Between LRRD and GND
Tester Range 2 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)


h.
E285133E07
2.927,1.365 3.302,1.615 0.375,0.25 10 false GND

Waveform 4

i.

CAN communication signal

Item Content
Driving Support ECU Assembly Terminal Name Between CA2H and GND
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.