Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus:

i.

for Pre-Crash: Body Electrical / Pre-Crash / Data List.


ii.

for Pre-Crash 2: Body Electrical / Pre-Crash 2 / Data List.



e.

Read the Data List according to the display on the GTS.

HINT:

As the driving support ECU and seat belt control ECU both have Data List for the pre-crash system, be sure to check the Pre-Crash and Pre-Crash 2 Data Lists.


Pre-Crash
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Driver Buckle SW Buckle switch status of driver side seat/
UNKNOWN, UNSET, SET or ERROR
UNKNOWN: Indeterminate data
UNSET: Driver seat belt unfastened
SET: Driver seat belt fastened
ERROR: Buckle switch trouble
-
Passenger Buckle SW Buckle switch status of passenger side seat/
UNKNOWN, UNSET, SET or ERROR
UNKNOWN: Indeterminate data
UNSET: Driver seat belt unfastened
SET: Driver seat belt fastened
ERROR: Buckle switch trouble
-
Driver Belt Control Seat belt control status of driver side seat/
UNSPPRT, STOP, ON or UNKNOWN
UNSPPRT: Seat belt control unsupported
STOP: Control stopped
ON: Controlled
UNKNOWN: Indeterminate data
Seat belt (driver side) is fastened
Passenger Belt Control Seat belt control status of passenger side seat/
UNSPPRT, STOP, ON or UNKNOWN
UNSPPRT: Seat belt control unsupported
STOP: Control stopped
ON: Controlled
UNKNOWN: Indeterminate data
Seat belt (passenger side) is fastened
Number of Trouble Code Number of past trouble codes/min: 0, max: 255 Number of DTCs will be displayed -

Pre-Crash 2
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wiper Information Wiper operational status/
Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo, Hi
The respective operational status displayed -
Pre-Crash Brake OFF Switch Pre-crash system cancel switch assembly status/
ON or OFF
ON: Pre-crash system cancel switch assembly on
OFF: Pre-crash system cancel switch assembly off
-
Pre-Crash System Pre-crash system control/
Valid or Inval
Valid: Pre-crash system control not possible
Inval: Pre-crash system control possible
-
DCam Indicator Driver camera indicator display request signal/
ON or OFF
ON: Driver camera indicator display requested
OFF: Driver camera indicator display not requested
Not Supported
PCS Indicator "CHECK PCS SYSTEM" display request signal/
ON or OFF
ON: "CHECK PCS SYSTEM" display requested
OFF: "CHECK PCS SYSTEM" display not requested
-
PCS Disabled Indicator "PCS TEMPORARILY NOT AVAILABLE" display request signal/
ON or OFF
ON: "PCS TEMPORARILY NOT AVAILABLE" display requested
OFF: "PCS TEMPORARILY NOT AVAILABLE" display not requested
-
Pre-Crash Safety Warning Ind PCS system warning status/
ON or OFF
ON: Pre-crash warning indicator on
OFF: Pre-crash warning indicator off
-
Pre-Crash Safety Brake Ind PCS system "BRAKE!" alert status/
ON or OFF
ON: PCS system "BRAKE!" alert on
OFF: PCS system "BRAKE!" alert off
-
Pre-Crash Safety Warning Buz PCS system warning buzzer/
Valid or Inval
Valid: PCS system warning buzzer operation possible
Inval: PCS system warning buzzer operation not possible
-
Pre-Crash Brake Pre-crash brake function/
Valid or Inval
Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible
-
Front Radar PSB Front radar-linked pre-crash seat belt activation signal/
ON or OFF
ON: Front radar-linked pre-crash seat belt activated
OFF: Front radar-linked pre-crash seat belt not activated
Status changes when the pre-crash seat belt is activated before a crash
PBA Start Pre-crash brake assist activation signal/
ON or OFF
ON: Pre-crash brake assist activated
OFF: Pre-crash brake assist not activated
Signal status changes when the pre-crash brake assist is activated before a crash
(Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
Warning Brake Warning brake activation/
ON or OFF
ON: Warning brake operation activated
OFF: Warning brake operation not activated
Not Supported
Brake Assist Standby Supplemental brake pressure signal/
ON or OFF
ON: Supplemental brake pressure being provided
OFF: Supplemental brake pressure not being provided
Signal status changes when supplemental brake pressure is being provided after a crash is judged as unavoidable and before the brake pedal is depressed
Pre-Crash Brake Control Pre-crash brake operational status/
ON or OFF
ON: Pre-crash brake operating
OFF: Pre-crash brake function not operating
Status changes when pre-crash brake operates before a crash
AVS Start AVS control activation status/
ON or OFF
ON: AVS control activated
OFF: AVS control not activated
Status changes when the suspension is controlled (stiffened) prior to a crash
CCS Cancel Automatic cancellation of cruise control during pre-crash brake activation/
ON or OFF
ON: Cruise control automatically canceled
OFF: Cruise control not automatically canceled
-
Front Radar-Dirt History Millimeter wave radar sensor assembly dirt history/
ON or OFF
ON: History of excessive dirt
OFF: No history of excessive dirt
-
Front Radar-Environment Hist Millimeter wave radar sensor environment condition history/
Good or Bad
Good: No history of excessive bad environment
Bad: History of excessive bad environment
-
Curr Com PCS-WIL-R Driver seat active headrest ECU connection status/
without or with
with: Driver seat active headrest ECU connected
without: Driver seat active headrest ECU not connected
Not Supported
Curr Com PCS-WIL-L Front passenger seat active headrest ECU connection status/
without or with
with: Front passenger seat active headrest ECU connected
without: Front passenger seat active headrest ECU not connected
Not Supported
Curr Com Night View ECU Night view ECU connection status/
without or with
with: Night view ECU connected
without: Night view ECU not connected
Not Supported
Country# (DSS) Destination country for driving support computer/
JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC, NOFIX
Actual country code -
The Number of DTCs Number of DTCs/
0 to 255
When system is normal: 0
When a malfunction is detected: More than 0
-



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash / Active Test.


e.

Enter the following menus:

i.

for Pre-Crash: Body Electrical / Pre-Crash / Active Test.


ii.

for ABS/VSC/TRAC: Chassis / ABS/VSC/TRAC / Active Test.


iii.

for Main Body: Body Electrical / Main Body / Active Test.



f.

Perform Active Test according to the display on the GTS.

HINT:

The power switch must be turned on (IG) to proceed with the Active Test using the GTS.


Pre-Crash
Tester Display Test Part Control Range Diagnostic Note
Driver Seat Belt Motor Driver seat belt motor ON: Seat belt motor operates
OFF: Seat belt motor does not operate
Seat belt (driver side) is fastened
Passenger Seat Belt Motor Passenger seat belt motor ON: Seat belt motor operates
OFF: Seat belt motor does not operate
Seat belt (front passenger side) is fastened
Driver and Passenger Seat Belt Motor Driver and passenger seat belt motors ON: Seat belt motors operate
OFF: Seat belt motors do not operate
Seat belts (driver and front passenger sides) are fastened
Seat Belt Motor Backwards Operation Driver and passenger seat belt motors ON: Seat belt motors operate
OFF: Seat belt motors do not operate
The current reversed with the time of crash forecast is sent, and a motor is made to rotate in the direction of drawing a belt.

NOTICE:
·

The seat belt motor will only operate when the tongue plate is inserted into the buckle (seat belt fastened).

·

To prevent overheating the belt motor, this test cannot be activated continuously. Operate the belt motor at an interval of 30 seconds or more.



ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
DSS Signal Buzzer Skid control buzzer Buzzer ON/OFF Buzzer can be heard

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG SW Power switch IG signal/ON or OFF ON: Power switch on (IG)
OFF: Power switch off
-