Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2014.11–2017.12
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.


e.

Enter the following menus: Powertrain / Radar Cruise / Data List.


f.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


g.

Read the Data List according to the display on the GTS.

Pre-Crash 2
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wiper Information Wiper operational status/
Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo, Hi
The respective operational status displayed -
Pre-Crash Brake OFF Switch Pre-crash system cancel switch assembly status/
ON or OFF
ON: Pre-crash system cancel switch assembly on
OFF: Pre-crash system cancel switch assembly off
-
Pre-Crash System Pre-crash system control/
Valid or Inval
Valid: Pre-crash system control not possible
Inval: Pre-crash system control possible
-
DCam Indicator Driver camera indicator display request signal/
ON or OFF
ON: Driver camera indicator display requested
OFF: Driver camera indicator display not requested
Not Supported
PCS Indicator "PRE-CRASH SAFETY MALFUNCTION VISIT YOUR DEALER" display request signal/
ON or OFF
ON: "PRE-CRASH SAFETY MALFUNCTION VISIT YOUR DEALER" display requested
OFF: "PRE-CRASH SAFETY MALFUNCTION VISIT YOUR DEALER" display not requested
-
PCS Disabled Indicator "PRE-CRASH SAFETY UNAVAILABLE" display request signal/
ON or OFF
ON: "PRE-CRASH SAFETY UNAVAILABLE" display requested
OFF: "PRE-CRASH SAFETY UNAVAILABLE" display not requested
-
Pre-Crash Safety Warning Ind PCS system warning status/
ON or OFF
ON: Pre-crash warning indicator on
OFF: Pre-crash warning indicator off
-
Pre-Crash Safety Brake Ind PCS system "BRAKE!" alert status/
ON or OFF
ON: PCS system "BRAKE!" alert on
OFF: PCS system "BRAKE!" alert off
-
Pre-Crash Safety Warning Buz PCS system warning buzzer/
Valid or Inval
Valid: PCS system warning buzzer operation possible
Inval: PCS system warning buzzer operation not possible
-
Pre-Crash Brake Pre-crash brake function/
Valid or Inval
Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible
-
Front Radar PSB Front radar-linked pre-crash seat belt activation signal/
ON or OFF
ON: Front radar-linked pre-crash seat belt activated
OFF: Front radar-linked pre-crash seat belt not activated
Not Supported
PBA Start Pre-crash brake assist activation signal/
ON or OFF
ON: Pre-crash brake assist activated
OFF: Pre-crash brake assist not activated
Signal status changes when the pre-crash brake assist is activated before a crash
(Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
Warning Brake Warning brake activation/
ON or OFF
ON: Warning brake operation activated
OFF: Warning brake operation not activated
Not Supported
Brake Assist Standby Supplemental brake pressure signal/
ON or OFF
ON: Supplemental brake pressure being provided
OFF: Supplemental brake pressure not being provided
Signal status changes when supplemental brake pressure is being provided after a crash is judged as unavoidable and before the brake pedal is depressed
Pre-Crash Brake Control Pre-crash brake operational status/
ON or OFF
ON: Pre-crash brake operating
OFF: Pre-crash brake function not operating
Status changes when pre-crash brake operates before a crash
AVS Start AVS control activation status/
ON or OFF
ON: AVS control activated
OFF: AVS control not activated
Status changes when the suspension is controlled (stiffened) prior to a crash
CCS Cancel Automatic cancellation of cruise control during pre-crash brake activation/
ON or OFF
ON: Cruise control automatically canceled
OFF: Cruise control not automatically canceled
-
Front Radar-Dirt History Millimeter wave radar sensor assembly dirt history/
ON or OFF
ON: History of excessive dirt
OFF: No history of excessive dirt
-
Front Radar-Environment Hist Millimeter wave radar sensor environment condition history/
Good or Bad
Good: No history of excessive bad environment
Bad: History of excessive bad environment
-
Curr Com PCS-WIL-R Driver seat active headrest ECU connection status/
without or with
with: Driver seat active headrest ECU connected
without: Driver seat active headrest ECU not connected
Not Supported
Curr Com PCS-WIL-L Front passenger seat active headrest ECU connection status/
without or with
with: Front passenger seat active headrest ECU connected
without: Front passenger seat active headrest ECU not connected
Not Supported
Curr Com Night View ECU Night view ECU connection status/
without or with
with: Night view ECU connected
without: Night view ECU not connected
Not Supported
Country# (DSS) Destination country for driving support computer/
JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC, NOFIX
Actual country code -
The Number of DTCs Number of DTCs/
0 to 255
When system is normal: 0
When a malfunction is detected: More than 0
-

Radar Cruise
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Country# (F Radar Sens) Millimeter wave radar sensor country signal/JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC, NOFIX Actual country code -

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light switch assembly (STOP LP) output/
ON or OFF
ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.


f.

Perform Active Test according to the display on the GTS.

HINT:

The power switch must be turned on (IG) to proceed with the Active Test using the GTS.


Pre-Crash 2
Tester Display Test Part Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON/OFF Buzzer can be heard
PCS Approach Alarm Buzzer Skid control buzzer ON/OFF Buzzer can be heard

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop light switch assembly ON/OFF Stop lights come on