Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2014.11–2016.05
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A41  Brake Request Value Mismatch between ENG / EHV and Driving Support ECU  


DESCRIPTION

The brake booster with master cylinder (skid control ECU) receives brake control request signals from the power management control ECU and driving support ECU assembly.

When the request signals received from the power management control ECU and driving support ECU assembly are not consistent, the brake booster with master cylinder (skid control ECU) determines that a malfunction has occurred and sends a malfunction signal to the driving support ECU assembly.

If the driving support ECU assembly receives a malfunction signal, DTC C1A41 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A41 While the power switch is on (IG), a brake request signal from the power management control ECU and driving support ECU assembly are inconsistent for 3 seconds.
·

Electronically controlled brake system

·

Hybrid control system

·

Brake booster with master cylinder (skid control ECU)

·

Power management control ECU

·

Driving support ECU assembly



PROCEDURE

1.CHECK DTC OUTPUT (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Check DTCs for the electronically controlled brake system (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

OK:

Electronically controlled brake system DTC is not output.




OK

2.CHECK DTC OUTPUT (HYBRID CONTROL SYSTEM)

NG

2.CHECK DTC OUTPUT (HYBRID CONTROL SYSTEM)
a.

Check DTCs for the hybrid control system (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).

OK:

Hybrid control system DTC is not output.




OK

3.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER (SKID CONTROL ECU)

NG

3.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER (SKID CONTROL ECU)
a.

Replace the brake booster with master cylinder (skid control ECU) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL (for LHD), See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL (for RHD)).



NEXT

4.CHECK DTC OUTPUT (PRE-CRASH SYSTEM)
4.CHECK DTC OUTPUT (PRE-CRASH SYSTEM)
a.

Using the GTS, enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



c.

Recheck for DTCs.

OK:

DTC C1A41 is not output.




OK

END BRAKE BOOSTER WITH MASTER CYLINDER (SKID CONTROL ECU) WAS DEFECTIVE

NG

5.REPLACE POWER MANAGEMENT CONTROL ECU
5.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Replace the power management control ECU (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL).



NEXT

6.CHECK DTC OUTPUT (PRE-CRASH SYSTEM)
6.CHECK DTC OUTPUT (PRE-CRASH SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus:

i.

Body Electrical / Pre-Crash 2 / Trouble Codes.




f.

Recheck for DTCs.

OK:

DTC C1A41 is not output.




OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

NG

REPLACE DRIVING SUPPORT ECU ASSEMBLY