71848C
1.REMOVE SEAT ADJUSTER COVER CAP
Remove the seat adjuster cover cap.
Use the same procedure for the RH side and LH side.
71826B
2.REMOVE REAR SEAT CUSHION MOULDING LH
Remove the 2 screws.
Disengage the 8 claws and clip to remove the rear seat cushion moulding LH.
71829B
3.REMOVE REAR SEAT CUSHION MOULDING RH
Remove the 2 screws.
Disengage the 8 claws and clip to remove the rear seat cushion moulding RH.
73380D
4.REMOVE REAR SEAT INNER BELT ASSEMBLY
73350C
5.REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY
71865
6.REMOVE REAR NO. 1 SEAT BEZEL COVER
Remove the screw and rear No. 1 seat bezel cover.
7.REMOVE NO. 1 SEAT CUSHION COVER WITH PAD
Disengage the 5 hooks.
Disengage each hook and remove the No. 1 seat cushion cover with pad.
79012
8.REMOVE NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY
Remove the 6 hog rings.
Remove the 16 hog rings and remove the No. 1 seat cushion cover sub-assembly from the No. 1 seat cushion pad sub-assembly.
71882A
9.REMOVE REAR SEATBACK BOARD
Hold the rear seatback board at the position shown in the illustration.
Push the rear seatback board in the direction indicated by the arrow (1) shown in the illustration.
Pull the rear seatback board in the direction indicated by the arrow (2) shown in the illustration to disengage the claw (A).
Disengage the claw (B).
Use the same procedure as for the claw (A).
Disengage the 2 claws and remove the rear seatback board as shown in the illustration.
72615A
10.REMOVE REAR SEATBACK LOCK STRIKER COVER
Using a screw driver with its tips wrapped with protective tape, disengage the guide and claw, and remove the rear seatback lock striker cover.
| *1 | Protective Tape |
72057
11.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
Remove the 2 screws.
Disengage the 2 guides.
Disengage the 2 cable clamps and remove the rear seat lock control lever sub-assembly.
71931B
12.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Disengage the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
13.REMOVE NO. 1 SEATBACK COVER WITH PAD
Disengage the 4 hooks.
Remove the 2 hog rings.
Remove the 3 hog rings.
Disengage the hook.
Use the same procedure for the RH side and LH side.
Disengage the hook.
Use the same procedure for the RH side and LH side.
Disengage the 2 hooks.
Remove the No. 1 seatback cover with pad from the rear seatback frame sub-assembly.
79014
14.REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY
Remove the 9 hog rings and remove the No. 1 seatback cover sub-assembly from the No. 1 seatback pad sub-assembly.
71834A
15.REMOVE REAR NO. 1 SEAT RECLINING COVER LH
Disengage the 2 claws and remove the rear No. 1 seat reclining cover LH.
71833A
16.REMOVE REAR NO. 1 SEAT RECLINING COVER RH
Use the same procedure as for the LH side.
71639
17.REMOVE REAR SEAT CUSHION HINGE COVER LH
Disengage the 2 guides <A>.
Disengage the claw.
Disengage the guide <B> and remove the rear seat cushion hinge cover LH as shown in the illustration.
71629A
18.REMOVE REAR SEAT CUSHION HINGE COVER RH
Disengage the 2 guides <A>.
Disengage the claw.
Disengage the guide <B> and remove the rear seat cushion hinge cover RH as shown in the illustration.
72590B
19.REMOVE RECLINING REMOTE CONTROL CABLE ASSEMBLY
Disengage the 2 cable clamps and remove the reclining remote control cable assembly.
71018
20.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY
Remove the 4 bolts and rear seatback frame sub-assembly from the rear seat cushion frame sub-assembly.
72173B
21.REMOVE REAR SEAT TRACK ADJUSTING HANDLE
Operate the rear seat track adjusting handle to slide the rear seat adjuster so that each rear seat track adjusting handle hole can be seen through each rear seat adjuster hole as shown in the illustration.
| *1 | Rear Seat Adjuster |
| *2 | Rear Seat Track Adjusting Handle |
| *a | Rear Seat Adjuster Hole |
| *b | Rear Seat Track Adjusting Handle Hole |
Insert a screwdriver into the rear seat adjuster hole as shown in the illustration and disengage the 2 claws.
| *1 | Rear Seat Adjuster |
| *2 | Rear Seat Track Adjusting Handle |
Remove the rear seat track adjusting handle from the rear seat cushion frame sub-assembly as shown in the illustration.