71849A
1.REMOVE SEAT ADJUSTER COVER CAP
Remove the seat adjuster cover cap.
Use the same procedure for the RH side and LH side.
72574A
2.REMOVE RECLINING CONTROL LEVER
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the reclining control lever.
| *1 | Protective Tape |
71826B
3.REMOVE REAR SEAT CUSHION MOULDING LH
Remove the 2 screws.
Disengage the 10 claws and clip to remove the rear seat cushion moulding LH.
71829B
4.REMOVE REAR SEAT CUSHION MOULDING RH
Remove the 2 screws.
Disengage the 8 claws and clip to remove the rear seat cushion moulding RH.
73390
5.REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY
71865
6.REMOVE REAR NO. 1 SEAT BEZEL COVER
Remove the screw and rear No. 1 seat bezel cover.
7.REMOVE NO. 1 SEAT CUSHION COVER WITH PAD
Disengage the 3 hooks.
Disengage each hook and remove the No. 1 seat cushion cover with pad.
79012
8.REMOVE NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY
Remove the 5 hog rings.
Remove the 16 hog rings and remove the No. 1 seat cushion cover sub-assembly from the No. 1 seat cushion pad sub-assembly.
71882A
9.REMOVE REAR SEATBACK BOARD
Hold the rear seatback board at the position shown in the illustration.
Push the rear seatback board in the direction indicated by the arrow (1) shown in the illustration.
Pull the rear seatback board in the direction indicated by the arrow (2) shown in the illustration to disengage the claw (A).
Disengage the claw (B).
Use the same procedure as for the claw (A).
Disengage the 2 claws to remove the rear seatback board as shown in the illustration.
72616A
10.REMOVE REAR SEATBACK LOCK STRIKER COVER
Using a screw driver with its tips wrapped with protective tape, disengage the guide and claw, and remove the rear seatback lock striker cover.
| *1 | Protective Tape |
72058A
11.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
Remove the 2 screws.
Disengage the 2 guides.
Disengage the 2 cable clamps and remove the rear seat lock control lever sub-assembly.
71931B
12.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Disengage the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
13.REMOVE NO. 1 SEATBACK COVER WITH PAD
Disengage the 4 hooks.
Remove the 2 hog rings.
Remove the 3 hog rings.
Disengage the 2 hooks.
Remove the No. 1 seatback cover with pad from the rear seatback frame sub-assembly.
79014
14.REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY
Remove the 2 hog rings.
Remove the 9 hog rings and remove the No. 1 seatback cover sub-assembly from the No. 1 seatback pad sub-assembly.
72597B
15.REMOVE NO. 1 RECLINING REMOTE CONTROL LEVER BEZEL
Disengage the claw and guide, and remove the No. 1 reclining remote control lever bezel.
72526B
16.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the No. 1 reclining adjuster release handle.
| *1 | Protective Tape |
71876B
17.REMOVE RECLINING ADJUSTER INSIDE COVER LH
Disengage the 2 claws and remove the reclining adjuster inside cover LH.
71875C
18.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure as for the LH side.
71834B
19.REMOVE NO. 2 REAR SEAT RECLINING COVER
Disengage the clip and 2 claws, and remove the No. 2 rear seat reclining cover.
71834A
20.REMOVE NO. 1 REAR SEAT RECLINING COVER
Use the same procedure as for the No. 2 rear seat reclining cover.
71639
21.REMOVE REAR SEAT CUSHION HINGE COVER
Disengage the 2 guides <A>.
Disengage the claw.
Disengage the guide <B> and remove the rear seat cushion hinge cover as shown in the illustration.
72552E
22.REMOVE RECLINING HINGE COVER
Disengage the 2 guides <A>.
Disengage the claw.
Disengage the guide <B> and remove the reclining hinge cover as shown in the illustration.
72590B
23.REMOVE RECLINING REMOTE CONTROL CABLE ASSEMBLY
Remove the 2 clamps.
Disengage the 2 cable clamps and remove the reclining remote control cable assembly.
79956C
24.REMOVE REAR SEAT LEG SIDE COVER
Disengage the 2 claws and guide, and remove the rear seat leg side cover.
71018
25.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY
Disengage the 2 cable clamps.
Remove the 4 bolts and rear seatback frame sub-assembly from the rear seat cushion frame sub-assembly.
72173B
26.REMOVE REAR SEAT TRACK ADJUSTING HANDLE
Operate the rear seat track adjusting handle to slide the rear seat adjuster so that each rear seat track adjusting handle hole can be seen through each rear seat adjuster hole as shown in the illustration.
| *1 | Rear Seat Adjuster |
| *2 | Rear Seat Track Adjusting Handle |
| *a | Rear Seat Adjuster Hole |
| *b | Rear Seat Track Adjusting Handle Hole |
Insert a screwdriver into the rear seat adjuster hole as shown in the illustration and disengage the 2 claws.
| *1 | Rear Seat Adjuster |
| *2 | Rear Seat Track Adjusting Handle |
Remove the rear seat track adjusting handle from the rear seat cushion frame sub-assembly as shown in the illustration.