Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1442/42  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 blower damper servo sub-assembly (air inlet) sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air inlet mode selection air inlet control damper to any position, which controls the intake air settings (FRESH, FRESH/RECIRCULATION, and RECIRCULATION).

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

HINT:

Confirm that no mechanical problem is present because this DTC can be stored when either a damper link or the damper is mechanically locked.


DTC No. DTC Detection Condition Trouble Area
B1442/42 Air inlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 blower damper servo sub-assembly (air inlet).
·

No. 1 blower damper servo sub-assembly (air inlet)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E229253E12
5.728,2.187 5.825,2.362 0.097,0.174 10 3 5.728,1.235 5.825,1.409 0.097,0.174 10 4 5.948,2.281 6.404,2.456 0.456,0.174 10 BUS 5.948,3.237 6.404,3.412 0.456,0.174 10 BUS G 5.504,4.085 5.746,4.259 0.242,0.174 10 z11 5.504,4.243 7.089,4.575 1.585,0.332 10 Air Conditioning Amplifier Assembly 0.393,4.1 2.253,4.432 1.860,0.332 10 No. 1 Blower Damper Servo Sub-assembly (Air Inlet) 5.728,3.141 5.825,3.315 0.097,0.174 10 2 5.948,1.329 6.390,1.503 0.443,0.174 10 B BUS 3.076,4.085 4.631,4.466 1.555,0.382 10 Air Conditioning Harness Assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Operate the R/F (Recirculation/Fresh) switch.


e.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Inlet Damper Actual Pulse No. 1 blower damper servo sub-assembly (air inlet) actual pulse / Min.: 0, Max.: 255
for LHD:

RECIRCULATION: 19 (pulse)

FRESH: 7 (pulse)


for RHD:

RECIRCULATION: 7 (pulse)

FRESH: 25 (pulse)


-

OK:

The display is as specified in the Normal Condition column.


Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C




A

2.PERFORM ACTIVE TEST USING GTS

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Air Inlet Damper Targ Pulse No. 1 blower damper servo sub-assembly (air inlet) target pulse Min.: 0, Max.: 255
for LHD:

Operates between 7 to 19 pulses


for RHD:

Operates between 7 to 25 pulses



OK:

Recirculation damper position changes in accordance with each control range.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.INSPECT NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
3.INSPECT NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
a.

Replace the No. 1 blower damper servo sub-assembly (air inlet) (See page Vehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1442/42 is output A
DTC B1442/42 is not output B




A

4.INSPECT AIR CONDITIONING HARNESS ASSEMBLY

B

END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY WAS DEFECTIVE)

4.INSPECT AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1442/42 is output A
DTC B1442/42 is not output B




A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)