The No. 1 blower damper servo sub-assembly (air inlet) sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air inlet mode selection air inlet control damper to any position, which controls the intake air settings (FRESH, FRESH/RECIRCULATION, and RECIRCULATION).
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
Confirm that no mechanical problem is present because this DTC can be stored when either a damper link or the damper is mechanically locked.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1442/42 | Air inlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 blower damper servo sub-assembly (air inlet). | ·
No. 1 blower damper servo sub-assembly (air inlet) ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Operate the R/F (Recirculation/Fresh) switch.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Air Inlet Damper Actual Pulse | No. 1 blower damper servo sub-assembly (air inlet) actual pulse / Min.: 0, Max.: 255 | for LHD:
RECIRCULATION: 19 (pulse) FRESH: 7 (pulse) for RHD:
RECIRCULATION: 7 (pulse) FRESH: 25 (pulse) |
- |
The display is as specified in the Normal Condition column.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
A
B
(See pageVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>PROBLEM SYMPTOMS TABLE)
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Check the operation by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Inlet Damper Targ Pulse | No. 1 blower damper servo sub-assembly (air inlet) target pulse | Min.: 0, Max.: 255 | for LHD:
Operates between 7 to 19 pulses for RHD:
Operates between 7 to 25 pulses |
Recirculation damper position changes in accordance with each control range.
OK
NG
Replace the No. 1 blower damper servo sub-assembly (air inlet) (See page Vehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY).
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1442/42 is output | A |
| DTC B1442/42 is not output | B |
A
B
Replace the air conditioning harness assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1442/42 is output | A |
| DTC B1442/42 is not output | B |
A
B