Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM D

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Air conditioning system data and Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the GTS to check for malfunctions and perform troubleshooting.




LIST OF OPERATION METHODS


a.

By operating each of the air conditioning control switches as shown in the diagram below, it is possible to enter diagnostic check mode.

E228409E03
1.521,0.385 4.281,1.219 2.76,0.833 10 false Turn the power switch on (IG) while pressing the center cluster module circuit "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears. 4.615,1.198 6.677,1.76 2.063,0.563 10 false The "AUTO" and "Recirculation/Fresh" switches are not pressed at the same time. 2.208,2.74 3.615,3.083 1.406,0.344 10 false Indicator Check (continuous operation) 2.052,4.167 3.76,4.51 1.708,0.344 10 false Sensor Check (DTC check) (continuous operation) 2.052,5.604 3.76,5.948 1.708,0.344 10 false Sensor Check (DTC check) (step operation) 4.635,5.177 5.042,5.333 0.406,0.156 10 false AUTO 3.5,5.052 3.667,5.208 0.167,0.156 10 false *1 3.188,6.479 3.354,6.635 0.167,0.156 10 false *1 1.5,7.188 4.281,7.344 2.781,0.156 10 false Cancel check mode and start the A/C control 1,2.792 1.323,2.948 0.323,0.156 10 false OFF 1,4.229 1.323,4.385 0.323,0.156 10 false OFF 0.917,8.146 2.625,8.302 1.708,0.156 10 false : Indicates switch operation 0.635,8.479 1.76,8.635 1.125,0.156 10 false OFF: OFF switch 2.885,8.479 5.229,8.635 2.344,0.156 10 false *1: Micro dust and pollen filter switch 2.885,8.146 5.438,8.302 2.552,0.156 10 false AUTO: AUTO switch



INDICATOR CHECK


a.

Turn the power switch off.


b.

Turn the power switch on (ACC) and wait at least 5 seconds.


c.

Turn the power switch on (IG) while pressing the air conditioning control assembly "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears.

E250409E01
0.236,0.25 0.548,0.394 0.312,0.145 10 *A 3.701,0.25 4.013,0.394 0.312,0.145 10 *B

Text in Illustration
*A for LHD *B for RHD


d.

The indicator check is automatically performed when panel diagnosis is activated. Check that the indicators light up and go off 4 times at 1-second intervals continuously.

E250410E01
0.325,0.262 0.636,0.407 0.312,0.145 10 *A 3.79,0.262 4.101,0.407 0.312,0.145 10 *B 2.211,2.294 2.523,2.438 0.312,0.145 10 *a 2.403,2.761 2.714,2.906 0.312,0.145 10 *b 2.403,3.333 2.714,3.478 0.312,0.145 10 *c 3.503,2.417 3.717,2.562 0.214,0.145 10 *d 2.792,2.417 3.104,2.562 0.312,0.145 10 *d

HINT:
·

The sensor check automatically starts when the indicator check is completed.

·

Press the "OFF" switch to cancel the check mode.



Text in Illustration
*A for LHD *B for RHD
*a Indicator Blinking Pattern *b ON
*c OFF *d 1 sec.



SENSOR CHECK (DTC CHECK)


a.

Start the hybrid system and warm it up.


b.

Perform the indicator check.

HINT:

After the indicator check is completed, the system enters DTC check mode automatically.



c.

Read the DTC displayed on the panel.

E250411E01
0.269,0.342 0.580,0.487 0.312,0.145 10 *A 3.734,0.342 4.045,0.487 0.312,0.145 10 *B 2.197,0.688 2.426,0.833 0.228,0.145 10 *a 1.794,1.046 1.95,0.749 1.95,0.749 2.146,0.749 false 5.889,0.679 6.117,0.823 0.228,0.145 10 *a 5.486,1.037 5.642,0.74 5.642,0.74 5.838,0.74 false

NOTICE:

In sensor check mode, which is automatically entered after indicator check mode, troubleshooting may be partially performed. Be sure to perform the sensor check again.


HINT:

Refer to Diagnostic Trouble Code Chart for details of the codes (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

·

When there are no problems, DTC 00 is output.

·

As an example, the illustration shows that panel DTC 12 is output.



Text in Illustration
*A for LHD *B for RHD
*a Diagnostic Trouble Code (DTC) - -


d.

If the steps are difficult to read because they change automatically, press the micro dust and pollen filter switch to display the steps one at a time so that they can be read easily. The items are displayed step by step each time the micro dust and pollen filter mode switch is pressed.

E250412E01
0.341,0.348 0.652,0.493 0.312,0.145 10 *A 3.806,0.348 4.118,0.493 0.312,0.145 10 *B

HINT:

Press the "OFF" switch to finish panel diagnosis.


Text in Illustration
*A for LHD *B for RHD


e.

Clear the DTC

i.

During the sensor check, press the "FRONT DEF" switch and pollen filter mode switch simultaneously.

E250413E01
0.315,0.339 0.626,0.484 0.312,0.145 10 *A 3.84,0.339 4.151,0.484 0.312,0.145 10 *B

Text in Illustration
*A for LHD *B for RHD