Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2013.08
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1497/97  BUS IC Communication Malfunction  


DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and the servos. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo through the air conditioning harness assembly. Each servo sends damper position information to the air conditioning amplifier assembly.

DTC No. DTC Detection Condition Trouble Area
B1497/97 Communication line error or open
·

Air conditioning harness assembly

·

No. 1 air conditioning radiator damper servo sub-assembly

·

No. 2 air conditioning radiator damper servo sub-assembly

·

No. 1 blower damper servo sub-assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E233245E11
4.576,2.111 7.028,2.452 2.452,0.341 10 No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Air Mix) 0.302,2.769 1.930,3.105 1.628,0.336 10 Air Conditioning Amplifier Assembly 4.646,0.457 6.422,0.650 1.776,0.193 10 from Auxiliary Battery 1.922,0.457 2.193,0.622 0.272,0.165 10 L17 3.132,0.597 3.701,0.763 0.569,0.165 10 ECU-B3 1.956,0.289 2.133,0.454 0.178,0.165 10 21 1.989,0.892 2.096,1.057 0.107,0.165 10 4 1.989,1.284 2.096,1.449 0.107,0.165 10 3 1.989,1.676 2.096,1.841 0.107,0.165 10 2 1.928,1.06 2.187,1.225 0.259,0.165 10 z11 1.928,1.452 2.186,1.617 0.258,0.165 10 z11 1.928,1.844 2.170,2.010 0.242,0.165 10 z11 1.393,1.844 1.882,2.010 0.489,0.165 10 BUS G 1.541,1.452 1.869,1.617 0.329,0.165 10 BUS 1.393,1.06 1.903,1.225 0.509,0.165 10 B BUS 3.313,0.976 3.746,1.141 0.433,0.165 10 BBUS 3.313,1.368 3.642,1.533 0.329,0.165 10 BUS 3.313,1.752 3.742,1.917 0.430,0.165 10 BUSG 1.747,0.457 1.871,0.622 0.124,0.165 10 B 4.758,5.893 6.543,6.234 1.786,0.341 10 No. 1 Blower Damper Servo Sub-assembly (Air Inlet) 4.576,4.03 7.083,4.371 2.508,0.341 10 No. 2 Air Conditioning Radiator Damper Servo Sub-Assembly (Air Outlet)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active test.


e.

Check the operation by referring to the table below.

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (air mix) pulse Min.: 0, Max.: 255 Operates between 6 to 93 pulses
Air Outlet Servo Pulse (D) No. 1 blower damper servo sub-assembly (air outlet) pulse Min.: 0, Max.: 255 Operates between 5 to 47 pulses
Air Inlet Damper Targ Pulse No. 2 air conditioning radiator damper servo sub-assembly (air inlet) target pulse Min.: 0, Max.: 255
for LHD:

Operates between 7 to 19 pulses


for RHD:

Operates between 7 to 25 pulses



OK:

Arm of the damper servo motor selected in the Active Test moves smoothly.



f.

According to the test result, proceed to the next step.


Result:
Result Proceed to
One of the damper servo motors is malfunctioning A
All of the damper servo motors are malfunctioning B



A

2.SYSTEM CHECK

B

6.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
2.SYSTEM CHECK
a.

According to the test result, proceed to the next step.


Result:
Result Proceed to
Only the No. 1 air conditioning radiator damper servo sub-assembly (air mix) is malfunctioning A
Only the No. 2 air conditioning radiator damper servo sub-assembly (air inlet) is malfunctioning B
Only the No. 1 blower damper servo sub-assembly (air outlet) is malfunctioning C



A

3.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX)

B

4.REPLACE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR INLET)

C

5.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET)
3.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX)
a.

Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1497 is not output A
DTC B1497 is output B




A

END

B

6.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
4.REPLACE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
a.

Replace the No. 2 air conditioning radiator damper servo sub-assembly (air inlet) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1497 is not output A
DTC B1497 is output B




A

END

B

6.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
5.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET)
a.

Replace the No. 1 blower damper servo sub-assembly (air outlet) (See page Vehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1497 is not output A
DTC B1497 is output B




A

END

B

6.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
6.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1497 is not output A
DTC B1497 is output B




A

END

B

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
7.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Disconnect the L17 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L17-21 (B) - Body ground Power switch off 11 to 14 V




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR