Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Air Conditioning Control Panel Circuit  


DESCRIPTION

Center cluster module circuit (air conditioning control assembly) switch signals are sent to the air conditioning amplifier assembly via LIN communication.

WIRING DIAGRAM

E254310E01
2.256,0.634 2.578,0.808 0.323,0.174 10 A/C 2.966,0.396 3.196,0.570 0.230,0.174 10 16 3.068,0.956 3.196,1.130 0.128,0.174 10 1 4.329,0.62 4.457,0.794 0.128,0.174 10 3 5.366,0.62 5.550,0.794 0.184,0.174 10 37 0.098,0.48 1.555,0.654 1.457,0.174 10 from IG1 NO. 1 Relay 3.236,0.48 3.522,0.654 0.286,0.174 10 IG+ 3.979,0.76 4.264,0.934 0.286,0.174 10 TX+ 5.604,0.76 5.959,0.934 0.355,0.174 10 LIN1 0.841,2.357 2.478,2.532 1.637,0.174 10 : LIN Communication Line 3.236,1.04 3.610,1.215 0.373,0.174 10 GND 2.788,1.516 3.050,1.691 0.262,0.174 10 L20 2.788,1.671 4.652,2.192 1.864,0.522 10 Center Cluster Module Circuit (Air Conditioning Control Assembly) 5.31,1.53 5.572,1.705 0.262,0.174 10 L17 5.31,1.671 6.964,2.026 1.654,0.356 10 Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE CIRCUIT - POWER SOURCE)
a.

Disconnect the L20 center cluster module circuit (air conditioning control assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L20-16 (IG+) - Body ground Power switch off Below 1 V
Power switch on (IG) 11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE CIRCUIT - GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE CIRCUIT - GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L20-1 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - CENTER CLUSTER MODULE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - CENTER CLUSTER MODULE CIRCUIT)
a.

Disconnect the L17 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L20-3 (TX+) - L17-37 (LIN1) Always Below 1 Ω
L20-3 (TX+) - Body ground Always 10 kΩ or higher




OK

4.REPLACE CENTER CLUSTER MODULE CIRCUIT (AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE CENTER CLUSTER MODULE CIRCUIT (AIR CONDITIONING CONTROL ASSEMBLY)
a.

Replace the center cluster module circuit (air conditioning control assembly) with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>DISASSEMBLY).

OK:

The center cluster module circuit (air conditioning control assembly) operation returns to normal.




OK

END (CENTER CLUSTER MODULE CIRCUIT WAS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE