Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT EVAPORATOR TEMPERATURE SENSOR › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301849 FRONT EVAPORATOR TEMPERATURE SENSOR A

HEATING / AIR CONDITIONING  FRONT EVAPORATOR TEMPERATURE SENSOR  INSTALLATION  


PROCEDURE

Hide 88625 1.INSTALL NO. 1 COOLER THERMISTOR

a.

for HFC-134a (R134a):

i.
E189064E04
2.26,0.354 2.479,0.354 2.479,0.354 2.552,0.594 false 2.219,2.563 2.031,2.771 true 2.323,2.563 2.542,2.802 true 2.969,0.729 3.104,0.615 false 0.521,1.875 0.729,2.073 0.208,0.198 10 false A 0.521,2.052 0.698,2.24 0.177,0.188 10 false B 0.531,2.25 0.688,2.438 0.156,0.188 10 false C 0.677,2.677 0.865,2.833 0.188,0.156 10 false D 2.125,0.26 2.219,0.406 0.094,0.146 10 false a 3.146,0.5 3.313,0.729 0.167,0.229 10 false b 2.792,0.208 2.906,0.344 0.115,0.135 10 false X 1.844,2.708 2.021,2.927 0.177,0.219 10 true *a 2.552,2.729 2.729,2.948 0.177,0.219 10 true *b

Install the No. 1 cooler thermistor as shown in the illustration.

Part Length
A 175 mm 6.89 in.
B 161.6 mm 6.36 in.
C 87.9 mm 3.46 in.
D 50 mm 1.97 in.

Text in Illustration
*a Fixed Part
*b Sensor Part

NOTICE:
·

Be sure to insert the thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

·

When reusing the evaporator, insert the thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the thermistor, do not apply excessive force to the wire.

·

Directly insert the thermistor until the edge of plastic case "a" comes into contact with evaporator "b".





b.

for HFO-1234yf (R1234yf):

i.
E278550E02
2.51,1.365 2.823,1.073 false 2.177,1.333 1.854,0.885 true 2.063,3.313 2.24,3.677 true 2.271,3.302 2.615,3.563 true 2.313,0.5 2.5,0.688 0.188,0.188 10 false X 1.719,0.729 1.906,0.917 0.188,0.188 10 false a 2.854,0.938 3.042,1.125 0.188,0.188 10 false b 1.531,2.771 1.719,2.958 0.188,0.188 10 false B 1.531,2.271 1.719,2.458 0.188,0.188 10 false A 1.094,3.552 1.281,3.74 0.188,0.188 10 false C 2.198,3.688 2.406,3.875 0.208,0.188 10 true *a 2.635,3.5 2.844,3.688 0.208,0.188 10 true *b

Install the No. 1 cooler thermistor as shown in the illustration.

Part Length
A 34.3 mm 1.35 in.
B 20.9 mm 0.823 in.
C 50 mm 1.97 in.

Text in Illustration
*a Fixed Part
*b Sensor Part

NOTICE:
·

Be sure to insert the thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

·

When reusing the evaporator, insert the thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the thermistor, do not apply excessive force to the wire.

·

Directly insert the thermistor until the edge of plastic case "a" comes into contact with evaporator "b".





Hide 88501 2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

Hide 5.INSTALL AIR CONDITIONING UNIT ASSEMBLY