Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061948 INTERIOR PANELS / TRIM _0301857 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  UPPER INSTRUMENT PANEL  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

(See page Vehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>PRECAUTION)

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 7.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 8.REMOVE INTEGRATION CONTROL AND PANEL

a.
B282815

Disengage the 8 claws.


b.

Disconnect each connector and remove the integration control and panel.


Hide 55431B 9.REMOVE UPPER INSTRUMENT PANEL FINISH PANEL

a.
B282816

Disengage the 2 claws and clip and remove the upper instrument panel finish panel.


Hide 55480D 10.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.
B318028

Disengage the 8 claws and clip.


b.

Disconnect each connector and remove the lower instrument panel finish panel assembly.


Hide 55044B 11.REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

a.
B282818

Using a moulding remover, disengage the 8 claws and remove the upper instrument panel finish panel sub-assembly.


Hide 12.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B313753

Using a moulding remover, disengage the 6 claws and remove the No. 1 instrument panel register assembly.


b.

w/ headup display:

i.

Disconnect the connector.



Hide 62312B 13.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Disconnect the front door opening trim weatherstrip LH.


Hide 55436A 14.REMOVE INSTRUMENT PANEL FINISH PANEL END LH

a.
B282820

Using a moulding remover, disengage the 6 claws and guide.


b.
B282821

Disengage the guide and remove the instrument panel finish panel end LH as shown in the illustration.


Hide 62212 15.REMOVE FRONT PILLAR GARNISH LH

Hide 62226 16.REMOVE LOWER FRONT PILLAR GARNISH LH

a.
B274883

Using a moulding remover, disengage the 3 claws and remove the lower front pillar garnish LH.


Hide 55408F 17.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.
B276258E03
1.573,1.531 2.01,1.583 true 2.052,1.531 2.208,1.677 0.156,0.146 10 false *1

Apply protective tape to the areas shown in the illustration.

Text in Illustration
*1 Protective Tape


b.
B274879

Using a moulding remover, disengage the 5 claws.


c.

Disengage the 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.


Hide 55440D 19.REMOVE INSTRUMENT PANEL BOX ASSEMBLY

a.
B282822

Open the instrument panel box and glove compartment door.


b.
B282823

Pull the instrument panel box assembly in the direction indicated by the arrow to disengage the 8 claws as shown in the illustration.


c.

Close the glove compartment door.


Hide 20.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B282824

Remove the screw <C>.


b.
B282825

Using a moulding remover, disengage the 6 claws and remove the No. 2 instrument panel register assembly.


Hide 55620C 21.REMOVE INSTRUMENT PANEL CUP HOLDER

a.
B282826

Remove the 2 screws <E> and instrument panel cup holder.


Hide 62311B 22.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 55435A 23.REMOVE INSTRUMENT PANEL FINISH PANEL END RH

a.
B318021

Using a molding remover, disengage the 6 claws and guide.


b.
B318022

Disengage the guide as shown in the illustration.


c.

Disconnect the connector to remove the instrument panel finish panel end RH.


Hide 62211 24.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 62225A 25.REMOVE LOWER FRONT PILLAR GARNISH RH

a.
B274881

Using a moulding remover, disengage the 3 claws and remove the lower front pillar garnish RH.


Hide 55409F 26.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.
B276257E03
2.219,1.677 1.458,1.75 true 1.25,1.688 1.406,1.833 0.156,0.146 10 false *1

Apply protective tape to the areas shown in the illustration.

Text in Illustration
*1 Protective Tape


b.
B273244

Using a moulding remover, disengage the 5 claws.


c.

Disengage the 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.


Hide 86160P 27.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

HINT:

Use the same procedure as for the LH side (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).


Hide 28.REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B282829

Disengage the 8 claws and remove the center instrument panel register assembly.


Hide 55406B 29.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B282830E03
1.51,2.75 1.729,2.948 0.219,0.198 10 true (1) 2.625,2.125 2.833,2.313 0.208,0.188 10 true (2)

Disengage the 2 claws and remove the lower center instrument cluster finish panel sub-assembly as shown in the illustration.


Hide 55085 30.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
B282831

Remove the 2 clips.


b.

Disengage the 2 guides and remove the No. 2 heater to register duct sub-assembly.


Hide 55404D 31.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B282832

Remove the 2 screws <D> and 3 clips.


b.
B282833

Disengage the 2 clips and 3 guides and remove the instrument cluster finish panel sub-assembly.


Hide 55414A 32.REMOVE INSTRUMENT CLUSTER FINISH PANEL END (w/ Headup Display)

a.
B313754E02
2.74,1.042 2.979,1.25 0.24,0.208 10 true (1) 2.729,0.458 2.927,0.625 0.198,0.167 10 false (2)

Pull the instrument cluster finish panel end in the direction indicated by the arrow (1) to disengage the 5 claws.


b.

Pull the instrument cluster finish panel end in the direction indicated by the arrow (2) to disengage the 2 guides and remove the instrument cluster finish panel end.


Hide 34.REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

a.

Disconnect the connector.

B282834


b.

Remove the 2 bolts <A> and 2 passenger airbag bolts <B>.

B282835E03
2.938,0.719 3.219,0.958 true 6.438,0.708 6.563,0.708 true 3.802,3.719 3.802,3.896 false 4.854,3.552 5.146,3.563 false 3.729,3.917 3.906,4.094 0.177,0.177 10 true *2 3.26,0.927 3.417,1.073 0.156,0.146 10 false *1 6.594,0.646 6.813,0.844 0.219,0.198 10 false *1 5.156,3.479 5.344,3.667 0.188,0.188 10 true *2

Text in Illustration
*1 Bolt <A> *2 Passenger Airbag Bolt <B>


c.

Disengage the 7 claws (A) as shown in the illustration.

B282836E03
2.667,2.115 2.865,2.281 0.198,0.167 10 true (1) 3.75,2.052 3.948,2.219 0.198,0.167 10 true (2) 0.156,2.531 0.385,2.698 0.229,0.167 10 true (A) 0.958,2.49 1.188,2.656 0.229,0.167 10 false (A) 1.635,2.208 1.865,2.375 0.229,0.167 10 true (A) 2.052,2.448 2.281,2.615 0.229,0.167 10 true (A) 4.104,2.615 4.333,2.781 0.229,0.167 10 true (A) 5.76,3.49 5.969,3.656 0.208,0.167 10 true (A) 6.552,3.802 6.781,3.969 0.229,0.167 10 false (A) 6.115,1.688 6.344,1.854 0.229,0.167 10 true (B) 5.083,1.583 5.313,1.75 0.229,0.167 10 true (B) 3.635,1.458 3.865,1.625 0.229,0.167 10 true (B) 2.542,1.625 2.771,1.792 0.229,0.167 10 true (B) 1.979,1.604 2.208,1.771 0.229,0.167 10 true (B)


d.

Disengage the 5 claws (B) and remove the upper instrument panel assembly as shown in the illustration.

NOTICE:
·

Do not damage the upper instrument panel assembly.

·

Do not allow the wire harnesses to interfere with the surrounding parts.