Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF SUNSHADE
RM2070E _58 Vehicle Interior _061948 INTERIOR PANELS / TRIM _0301861 ROOF SUNSHADE A

INTERIOR PANELS / TRIM  ROOF SUNSHADE  REASSEMBLY  


PROCEDURE

Hide 63303 1.INSTALL NO. 2 SUNSHADE TRIM SUB-ASSEMBLY

HINT:

Perform this procedure only when the No. 2 sunshade trim sub-assembly needs to be replaced.


a.

Remove the tape from a new No. 2 sunshade trim sub-assembly.


b.
B286228E03
0.833,0.458 1.021,0.625 true 1.833,1.5 2.333,1.198 true 0.948,1.667 1.146,1.833 0.198,0.167 10 false (1) 1.719,0.656 1.917,0.823 0.198,0.167 10 true (2) 0.948,0.625 1.125,0.781 0.177,0.156 10 true *1 2.354,1.094 2.51,1.24 0.156,0.146 10 false *2

Place a socket wrench on the hexagonal part shown in the illustration and turn the No. 2 sunshade trim assembly 17 times in the direction indicated by the arrow (1) shown in the illustration.

Text in Illustration
*1 Circular Hole
*2 Hexagonal Part

HINT:

Torque: 0.23 N*m (2.35 kgf*cm, 2.04 in.*lbf)



c.

Insert a 2.5 mm hexagon wrench into the circular hole of the No. 2 sunshade trim assembly as shown in the illustration.

NOTICE:

Make sure that the hexagon wrench does not fall out when installing the No. 2 sunshade trim assembly.



d.
B286229E03
2.604,4.219 2.635,4 true 0.771,1.125 0.792,0.823 false 0.688,1.125 0.854,1.292 0.167,0.167 10 true *1 0.5,4.083 0.698,4.25 0.198,0.167 10 false (1) 2.51,3.438 2.708,3.604 0.198,0.167 10 false (2) 2.521,4.219 2.677,4.365 0.156,0.146 10 false *2

As shown in the illustration, insert the guide so that the hexagon wrench is upright.

Text in Illustration
*1 Guide
*2 Pin


e.

Press the pin in the direction indicated by the arrow (1) shown in the illustration.


f.

Slide the No. 2 sunshade trim sub-assembly in the direction indicated by the arrow (2) shown in the illustration to install it.


g.

Remove the 2.5 mm hexagon wrench.

HINT:

Use the same procedure for the other side sunshade trim.



Hide 63306 2.INSTALL SUNSHADE TRIM SUB-ASSEMBLY

a.

Wrap the sunshade cover as shown in the illustration.

B274347E03
1.5,1.313 1.469,0.99 true 2.771,1.844 2.615,1.917 false 3.958,0.281 4.135,0.375 false 0.729,1.479 1.052,1.531 true 5.646,1.823 5.677,1.51 true 6.438,2.01 6.115,2.052 true 1.438,1.323 1.594,1.469 0.156,0.146 10 false *2 2.781,1.781 2.938,1.927 0.156,0.146 10 false *1 3.813,0.208 3.969,0.354 0.156,0.146 10 false *1 1.052,1.458 1.208,1.604 0.156,0.146 10 false *2 5.583,1.833 5.74,1.979 0.156,0.146 10 false *2 5.969,1.99 6.125,2.135 0.156,0.146 10 false *2

Text in Illustration
*1 Sunshade Cover *2 End of Sunshade Cover


b.

Insert the ends of the sunshade cover to the slide roof rail sub-assembly.


c.

Using a T20 "TORX" socket wrench, install the sunshade trim sub-assembly to the slide roof rail sub-assembly with the 4 "TORX" screws.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

Temporary install the 8 screws.


e.

Perform a gap check.

i.

Check that the clearance between each front sliding roof bracket plate and the sliding roof rail sub-assembly are as specified.

B396424E01
0.831,0.332 0.933,0.481 0.102,0.149 10 b 0.654,0.332 0.756,0.481 0.102,0.149 10 a 0.831,2.333 0.933,2.482 0.102,0.149 10 b 0.654,2.333 0.756,2.482 0.102,0.149 10 a 6.535,0.803 6.637,0.952 0.102,0.149 10 b 6.357,0.803 6.459,0.952 0.102,0.149 10 a 6.541,2.832 6.642,2.981 0.102,0.149 10 b 6.358,2.832 6.460,2.981 0.102,0.149 10 a 0.232,0.815 0.389,0.964 0.157,0.149 10 *2 0.333,1.686 0.490,1.835 0.157,0.149 10 *1 0.478,1.752 0.746,1.69 false 0.916,0.873 1.184,0.812 false 0.378,0.876 0.64,0.816 false 1.207,0.735 1.364,0.884 0.157,0.149 10 *2 5.933,2.475 6.090,2.624 0.157,0.149 10 *2 6.798,1.838 6.956,1.987 0.157,0.149 10 *1 6.524,1.973 6.792,1.911 false 6.632,2.546 6.837,2.498 false 6.079,2.545 6.341,2.484 false 6.846,2.435 7.004,2.584 0.157,0.149 10 *2

Text in Illustration
*1 Sliding Roof Bracket Plate *2 Sliding Roof Rail Sub-assembly
V100136

Front - -

Standard:

The clearance measurements of (a) and (b) shown in the illustration should be the same for both sliding roof bracket plates.


Reference Dimension:

Measurement (a) and (b): 1.5 mm


NOTICE:

If the clearance measurements are not the same, the sliding roof bracket plate and sliding roof rail sub-assembly may interfere with each other and cause noise.



ii.

Tighten the 4 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


iii.

Check that the clearance between each rear sliding roof bracket plate and the sliding roof rail sub-assembly are as specified.

B396438E01
0.789,0.36 0.891,0.509 0.102,0.149 10 b 0.612,0.36 0.714,0.509 0.102,0.149 10 a 0.789,2.389 0.891,2.538 0.102,0.149 10 b 0.604,2.389 0.706,2.538 0.102,0.149 10 a 6.43,0.817 6.532,0.966 0.102,0.149 10 b 6.245,0.817 6.347,0.966 0.102,0.149 10 a 6.429,2.874 6.530,3.023 0.102,0.149 10 b 6.246,2.874 6.348,3.023 0.102,0.149 10 a 0.185,1.851 0.343,2.000 0.157,0.149 10 *2 0.291,1.041 0.448,1.190 0.157,0.149 10 *1 0.436,1.108 0.704,1.046 false 0.885,2.078 1.153,2.016 false 0.331,1.913 0.593,1.852 false 1.175,1.94 1.333,2.089 0.157,0.149 10 *2 5.82,2.489 5.978,2.638 0.157,0.149 10 *2 6.686,1.431 6.844,1.580 0.157,0.149 10 *1 6.412,1.567 6.68,1.505 false 6.526,2.563 6.731,2.515 false 5.972,2.559 6.234,2.498 false 6.737,2.446 6.895,2.594 0.157,0.149 10 *2

Text in Illustration
*1 Sliding Roof Bracket Plate *2 Sliding Roof Rail Sub-assembly
V100136

Front - -

Standard:

The clearance measurements of (a) and (b) shown in the illustration should be the same for both sliding roof bracket plates.


Reference Dimension:

Measurement (a) and (b): 1.5 mm


NOTICE:

If the clearance measurements are not the same, the sliding roof bracket plate and sliding roof rail sub-assembly may interfere with each other and cause noise.



iv.

Tighten the 4 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)



Hide 63260H 3.INSTALL SLIDING ROOF DRIVE GEAR ASSEMBLY

a.
B274346

Install the sliding roof drive gear assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 63514A 4.INSTALL CONNECTOR WIRE

a.
B274345

Engage the 3 clamps.


b.

Connect the connector to install the connector wire.


Hide 63654A 5.INSTALL NO. 2 SUNSHADE GARNISH LH

a.
B284959

Install the No. 2 sunshade garnish LH with the 2 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 63653A 6.INSTALL NO. 2 SUNSHADE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 63652A 7.INSTALL NO. 1 SUNSHADE GARNISH LH

a.
B274343

Install the No. 1 sunshade garnish LH with the 2 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 63651A 8.INSTALL NO. 1 SUNSHADE GARNISH RH

HINT:

Use the same procedure as for the LH side.