Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF SUNSHADE SYSTEM
RM2070E _58 Vehicle Interior _061948 INTERIOR PANELS / TRIM _0301863 ROOF SUNSHADE SYSTEM C

INTERIOR PANELS / TRIM  ROOF SUNSHADE SYSTEM  B2342  Switch Failure  


DESCRIPTION

This DTC is output when the roof sunshade ECU (sliding roof drive gear assembly) detects that the roof sunshade switch is stuck for 30 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2342 Roof sunshade ECU (sliding roof drive gear assembly) detects roof sunshade switch is stuck for 30 seconds or more.
·

Roof sunshade ECU (Sliding roof drive gear assembly)

·

Roof sunshade switch (Map light assembly)

·

Wire harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION).



PROCEDURE

1.READ VALUE USING GTS (ROOF SUNSHADE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Sliding Roof / Data List.


e.

Read the Data List according to the display on the GTS.

Sliding Roof
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Open Switch Failure (Past) Open switch failure signal (Past)/ON or OFF ON: Roof sunshade open signal failure (Past)
OFF: Roof sunshade open signal not fail (Past)
-
Close Switch Failure (Past) Close switch failure signal (Past)/ON or OFF ON: Roof sunshade close signal failure (Past)
OFF: Roof sunshade close signal not fail (Past)
-
Open Switch Failure (Current) Open switch failure signal (Current)/ON or OFF ON: Roof sunshade open signal failure (Current)
OFF: Roof sunshade open signal not fail (Current)
-
Close Switch Failure (Current) Close switch failure signal (Current)/ON or OFF ON: Roof sunshade close signal failure (Current)
OFF: Roof sunshade close signal not fail (Current)
-

OK:

"OFF" appears on the GTS screen.




OK

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU - BODY GROUND)
a.

Disconnect the z21 roof sunshade ECU (sliding roof drive gear assembly) connector.


b.

Disconnect the U3 roof sunshade switch (map light assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z21-7 (OPN) - Body ground Always 10 kΩ or higher
z21-9 (CLS) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY)
a.
B270986E04
1.25,3.542 0.958,3.052 false 1.375,3.531 1.656,3.042 false 1.792,3.76 2.083,4.25 false 0.719,2.885 1.042,3.042 0.323,0.156 10 false OPN 0.177,0.156 0.333,0.313 0.156,0.156 10 false *a 1.604,2.885 1.896,3.042 0.292,0.156 10 false CLS 1.969,4.271 2.375,4.427 0.406,0.156 10 false GND1

Remove the roof sunshade switch (map light assembly) (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (CLS) - 15 (GND1) CLOSE switch is pressed Below 1 Ω
8 (CLS) - 15 (GND1) CLOSE switch is not pressed 10 kΩ or higher
9 (OPN) - 15 (GND1) OPEN switch is pressed Below 1 Ω
9 (OPN) - 15 (GND1) OPEN switch is not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Roof Sunshade Switch (Map Light Assembly))



OK

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPLACE ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY)