Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF SUNSHADE SYSTEM
RM2070E _58 Vehicle Interior _061948 INTERIOR PANELS / TRIM _0301863 ROOF SUNSHADE SYSTEM J

INTERIOR PANELS / TRIM  ROOF SUNSHADE SYSTEM  Roof Sunshade does not Move by Operating Roof Sunshade Switch  


DESCRIPTION

The roof sunshade ECU (sliding roof drive gear assembly) receives switch signals and drives its built-in motor.

WIRING DIAGRAM

B278931E01
0.775,4.354 2.445,4.505 1.670,0.151 10 : LIN Communication Line 4.814,3.513 6.392,3.988 1.577,0.475 10 Roof Sunshade ECU (Sliding Roof Drive Gear Assembly) 2.666,3.602 4.109,3.915 1.443,0.313 10 Roof Sunshade Switch (Map Light Assembly) 3.715,2.54 4.063,2.700 0.348,0.160 10 OPN 3.743,2.969 4.035,3.129 0.292,0.160 10 CLS 4.095,2.534 4.223,2.700 0.128,0.165 10 9 4.095,2.964 4.223,3.129 0.128,0.165 10 8 2.75,2.672 3.163,2.813 0.412,0.140 10 GND1 2.515,2.672 2.702,2.813 0.187,0.140 10 15 3.488,1.691 4.045,1.852 0.557,0.161 10 S/ROOF 0.191,1.504 1.562,1.665 1.372,0.161 10 from Auxiliary Battery 1.209,0.959 4.134,1.110 2.924,0.151 10 Main Body ECU (Multiplex Network Body ECU) 3.105,0.501 3.344,0.638 0.239,0.137 10 LIN 5.141,0.501 5.381,0.638 0.239,0.137 10 LIN 5.141,2.887 5.455,3.025 0.313,0.137 10 CLS 5.141,2.644 5.492,2.782 0.350,0.137 10 OPN 5.141,1.505 5.251,1.642 0.110,0.137 10 B 5.9,2.763 6.024,2.924 0.123,0.161 10 E 6.078,2.661 6.201,2.822 0.123,0.161 10 2 4.957,2.53 5.080,2.691 0.123,0.161 10 7 4.957,1.395 5.080,1.556 0.123,0.161 10 1 4.957,2.782 5.080,2.943 0.123,0.161 10 9 2.666,3.462 2.993,3.641 0.327,0.179 10 U3 4.814,3.364 5.086,3.543 0.272,0.179 10 z21

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the roof sunshade ECU (sliding roof drive gear assembly) is reinstalled or replaced, the roof sunshade ECU (sliding roof drive gear assembly) must be initialized (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION).

·

Since the roof sunshade system has functions that use LIN communication, first confirm that there is no malfunction in the LIN communication functions in accordance with the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Sliding Roof / Data List.


e.

Read the Data List according to the display on the GTS.


Sliding Roof
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Open Switch OPEN switch signal/ON or OFF ON: OPEN switch pressed
OFF: OPEN switch not pressed
-
Close Switch CLOSE switch signal/ON or OFF ON: CLOSE switch pressed
OFF: CLOSE switch not pressed
-

OK:

The GTS display changes according to switch operation as shown in the table.



OK

2.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU - AUXILIARY BATTERY, BODY GROUND)

NG

3.INSPECT ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU - AUXILIARY BATTERY, BODY GROUND)
a.

Disconnect the z21 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z21-1 (B) - Body ground Power switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z21-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY)
a.
B270986E05
1.24,3.531 0.948,3.042 false 1.375,3.521 1.656,3.031 false 1.792,3.76 2.083,4.25 false 0.719,2.854 1.042,3.01 0.323,0.156 10 false OPN 0.177,0.156 0.333,0.313 0.156,0.156 10 false *a 1.542,2.854 1.833,3.01 0.292,0.156 10 false CLS 1.969,4.271 2.375,4.427 0.406,0.156 10 false GND1

Remove the roof sunshade switch (map light assembly) (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (CLS) - 15 (GND1) CLOSE switch is pressed Below 1 Ω
8 (CLS) - 15 (GND1) CLOSE switch is not pressed 10 kΩ or higher
9 (OPN) - 15 (GND1) OPEN switch is pressed Below 1 Ω
9 (OPN) - 15 (GND1) OPEN switch is not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Roof Sunshade Switch (Map Light Assembly))



OK

4.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU - ROOF SUNSHADE SWITCH)

NG

REPLACE ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU - ROOF SUNSHADE SWITCH)
a.

Disconnect the U3 roof sunshade switch (map light assembly) connector.


b.

Disconnect the z21 roof sunshade ECU (sliding roof drive gear assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z21-9 (CLS) - U3-8 (CLS) Always Below 1 Ω
z21-9 (CLS) - Body ground Always 10 kΩ or higher
z21-7 (OPN) - U3-9 (OPN) Always Below 1 Ω
z21-7 (OPN) - Body ground Always 10 kΩ or higher
U3-15 (GND1) - Body ground Always Below 1 Ω
z21-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR