Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2012.03–2013.08
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301864 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


a.

Disconnect the O6*1 or N13*2 multiplex network master switch assembly connector.

·

*1: for LHD

·

*2: for RHD


U190803E03
3.063,0.156 3.344,0.365 0.281,0.208 10 false O6 3.354,0.156 3.885,0.802 0.531,0.646 10 false *A 3.667,0.167 4.031,0.417 0.365,0.25 10 false N13 3.99,0.146 4.438,0.427 0.448,0.281 10 false *B

Text in Illustration
*A for LHD *B for RHD


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
O6-11 (B) - O6-12 (GND) W - W-B Power supply Power switch off 11 to 14 V
O6-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
N13-11 (B) - N13-12 (GND) W - W-B Power supply Power switch off 11 to 14 V
N13-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the O6*1 or N13*2 multiplex network master switch assembly connector.

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
O6-15 (DOWN) - O6-12 (GND) L - W-B Power window motor DOWN output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
O6-15 (DOWN) - O6-12 (GND) L - W-B Power window motor DOWN output Power switch on (IG), driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
O6-18 (LED) - O6-12 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
O6-18 (LED) - O6-12 (GND) Y - W-B LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
O6-20 (UP) - O6-12 (GND) GR - W-B Power window motor UP output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
O6-20 (UP) - O6-12 (GND) GR - W-B Power window motor UP output Power switch on (IG), driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
N13-15 (DOWN) - N13-12 (GND) L - W-B Power window motor DOWN output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
N13-15 (DOWN) - N13-12 (GND) L - W-B Power window motor DOWN output Power switch on (IG), driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
N13-18 (LED) - N13-12 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
N13-18 (LED) - N13-12 (GND) Y - W-B LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
N13-20 (UP) - N13-12 (GND) GR - W-B Power window motor UP output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
N13-20 (UP) - N13-12 (GND) GR - W-B Power window motor UP output Power switch on (IG), driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

If the result is not as specified, the multiplex network master switch assembly may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


a.

Disconnect the N7*1 or O13*2 power window regulator switch assembly connector.

·

*1: for LHD

·

*2: for RHD


U190805E02
3.094,0.333 3.292,0.479 0.198,0.146 10 false N7 3.406,0.333 3.604,0.479 0.198,0.146 10 false *A 3.688,0.333 3.969,0.479 0.281,0.146 10 false O13 4.052,0.333 4.25,0.479 0.198,0.146 10 false *B

Text in Illustration
*A for LHD *B for RHD


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
N7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
O13-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the N7*1 or O13*2 power window regulator switch assembly connector.

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
N7-4 (LED) - N7-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
N7-4 (LED) - N7-1 (GND) GR - W-B LED illumination signal Approximately 43 seconds after the power switch turned off Below 1 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
N7-6 (UP) - N7-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
N7-7 (DOWN) - N7-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
N7-8 (AUTO) - N7-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
O13-4 (LED) - O13-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
O13-4 (LED) - O13-1 (GND) GR - W-B LED illumination signal Approximately 43 seconds after the power switch turned off Below 1 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
O13-6 (UP) - O13-1 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
O13-7 (DOWN) - O13-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
O13-8 (AUTO) - O13-1 (GND) BE - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V

If the result is not as specified, the power window regulator switch assembly may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)


a.

Disconnect the Q2 rear power window regulator switch assembly (for LH door) connector.

U154531E02
3.479,0.333 3.99,0.708 0.51,0.375 10 false Q2


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
Q2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the Q2 rear power window regulator switch assembly (for LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
Q2-4 (LED) - Q2-1 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
Q2-4 (LED) - Q2-1 (GND) Y - W-B LED illumination signal Approximately 43 seconds after the power switch turned off Below 1 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) Below 1 V
Q2-6 (UP) - Q2-1 (GND) L - W-B Power window motor UP output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) Below 1 V
Q2-7 (DOWN) - Q2-1 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) Below 1 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) Below 1 V
Q2-8 (AUTO) - Q2-1 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window fully open 11 to 14 V

If the result is not as specified, the rear power window regulator switch assembly (for LH door) may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)


a.

Disconnect the P2 rear power window regulator switch assembly (for RH door) connector.

U154532E02
3.49,0.333 3.75,0.521 0.26,0.188 10 false P2


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
P2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the P2 rear power window regulator switch assembly (for RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
P2-4 (LED) - P2-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
P2-4 (LED) - P2-1 (GND) GR - W-B LED illumination signal Approximately 43 seconds after the power switch turned off Below 1 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear RH door power window fully open 11 to 14 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) Below 1 V
P2-6 (UP) - P2-1 (GND) V - W-B Power window motor UP output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) Below 1 V
P2-7 (DOWN) - P2-1 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window fully open 11 to 14 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window fully open 11 to 14 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) Below 1 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) Below 1 V
P2-8 (AUTO) - P2-1 (GND) L - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window fully open 11 to 14 V

If the result is not as specified, the rear power window regulator switch assembly (for RH door) may have a malfunction.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


a.

Disconnect the O2*1 or N2*2 power window regulator motor assembly (for driver door) connector.

·

*1: for LHD

·

*2: for RHD


U190845E02
2.25,0.688 2.563,0.969 0.313,0.281 10 false O2 2.542,0.698 2.865,1.01 0.323,0.313 10 false *A 2.26,0.969 2.563,1.24 0.302,0.271 10 false N2 2.552,0.979 2.76,1.219 0.208,0.24 10 false *B

Text in Illustration
*A for LHD *B for RHD


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
O2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
O2-2 (B) - Body ground W - Body ground Power supply Power switch off 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
N2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
N2-2 (B) - Body ground W - Body ground Power supply Power switch off 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the O2*1 or N2*2 power window regulator motor assembly (for driver door) connector.

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
O2-5 (LED) - O2-1 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
O2-5 (LED) - O2-1 (GND) Y - W-B LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Automatic operation) Below 1 V
O2-7 (DOWN) - O2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Automatic operation) Below 1 V
O2-10 (UP) - O2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
N2-5 (LED) - N2-1 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
N2-5 (LED) - N2-1 (GND) Y - W-B LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Automatic operation) Below 1 V
N2-7 (DOWN) - N2-1 (GND) L - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Automatic operation) Below 1 V
N2-10 (UP) - N2-1 (GND) GR - W-B Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor assembly (for driver door) may have a malfunction.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)


a.

Disconnect the N2*1 or O2*2 power window regulator motor assembly (for front passenger door) connector.

·

*1: for LHD

·

*2: for RHD


U190846E02
2.25,0.688 2.542,0.906 0.292,0.219 10 false N2 2.583,0.698 2.823,0.927 0.24,0.229 10 false *A 2.25,0.969 2.521,1.177 0.271,0.208 10 false O2 2.583,0.969 2.813,1.198 0.229,0.229 10 false *B

Text in Illustration
*A for LHD *B for RHD


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
N2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
N2-2 (B) - Body ground W-B - Body ground Power supply Power switch off 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
O2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
O2-2 (B) - Body ground W-B - Body ground Power supply Power switch off 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the N2*1 or O2*2 power window regulator motor assembly (for front passenger door) connector.

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
N2-4 (AUTO) - N2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N2-5 (LED) - N2-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
N2-5 (LED) - N2-1 (GND) GR - W-B LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
N2-7 (DOWN) - N2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
N2-10 (UP) - N2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
O2-4 (AUTO) - O2-1 (GND) BE - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O2-5 (LED) - O2-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
O2-5 (LED) - O2-1 (GND) GR - W-B LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
O2-7 (DOWN) - O2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
O2-10 (UP) - O2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor assembly (for front passenger door) may have a malfunction.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)


a.

Disconnect the Q4 power window regulator motor assembly (for rear LH door) connector.

U154588E02
2.375,0.823 2.677,1.115 0.302,0.292 10 false Q4


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
Q4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
Q4-2 (B) - Body ground R - Body ground Power supply Power switch off 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the Q4 power window regulator motor assembly (for rear LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) Below 1 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) Below 1 V
Q4-4 (AUTO) - Q4-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q4-5 (LED) - Q4-1 (GND) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
Q4-5 (LED) - Q4-1 (GND) Y - W-B LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) Below 1 V
Q4-7 (DOWN) - Q4-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear LH door power window fully open 11 to 14 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) Below 1 V
Q4-10 (UP) - Q4-1 (GND) L - W-B Power window motor UP input Power switch on (IG), rear LH door power window fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor assembly (for rear LH door) may have a malfunction.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)


a.

Disconnect the P4 power window regulator motor assembly (for rear RH door) connector.

U154589E02
2.385,0.833 2.646,1.042 0.26,0.208 10 false P4


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
P4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
P4-2 (B) - Body ground R - Body ground Power supply Power switch off 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the P4 power window regulator motor assembly (for rear RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) Below 1 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) Below 1 V
P4-4 (AUTO) - P4-1 (GND) L - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P4-5 (LED) - P4-1 (GND) GR - W-B LED illumination signal Power switch on (IG) 11 to 14 V
P4-5 (LED) - P4-1 (GND) GR - W-B LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) Below 1 V
P4-7 (DOWN) - P4-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear RH door power window fully open 11 to 14 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) Below 1 V
P4-10 (UP) - P4-1 (GND) V - W-B Power window motor UP input Power switch on (IG), rear RH door power window fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor assembly (for rear RH door) may have a malfunction.



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Disconnect the MB and L8*1 main body ECU (multiplex network body ECU) connectors.

U191253E02
1.771,0.573 1.625,0.573 1.625,0.573 1.625,0.854 false 1.552,1.406 1.458,1.406 1.458,1.406 1.458,3.167 false 0.677,2.677 1.021,2.677 false 3.406,7.885 3.667,8.042 0.26,0.156 10 false MB 5.031,6.625 5.292,6.781 0.26,0.156 10 false 2A 1.781,6.583 2.042,6.74 0.26,0.156 10 false 2B 5.063,5.25 5.323,5.406 0.26,0.156 10 false 2C 1.792,5.281 2.052,5.438 0.26,0.156 10 false 2D 4.688,3.969 4.948,4.125 0.26,0.156 10 false 2E 4.979,3.969 5.24,4.125 0.26,0.156 10 false *B 5.656,3.979 5.917,4.135 0.26,0.156 10 false *C 5.354,3.969 5.615,4.125 0.26,0.156 10 false 2F 1.813,3.938 2.073,4.094 0.26,0.156 10 false L7 0.219,2.448 0.479,2.604 0.26,0.156 10 false 2E 0.521,2.448 0.781,2.604 0.26,0.156 10 false *B 0.521,2.74 0.781,2.896 0.26,0.156 10 false *C 0.229,2.74 0.49,2.896 0.26,0.156 10 false 2F 0.417,1.302 0.677,1.458 0.26,0.156 10 false 2D 0.417,2.052 0.677,2.208 0.26,0.156 10 false 2C 1.938,1.438 2.198,1.594 0.26,0.156 10 false L7 1.823,0.5 1.979,0.656 0.156,0.156 10 false *1 3.698,0.552 3.958,0.708 0.26,0.156 10 false MB 6.333,2.083 6.594,2.24 0.26,0.156 10 false 2A 6.323,1.406 6.583,1.563 0.26,0.156 10 false 2B 0.365,0.104 0.625,0.302 0.26,0.198 10 false *A 1.385,3.198 1.542,3.354 0.156,0.156 10 false *2

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 1 connector *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) *2 1 connector

U190870E02
1.781,0.677 1.625,0.677 1.625,0.677 1.625,0.958 false 1.542,1.406 1.458,1.406 1.458,1.406 1.458,3.281 false 1.552,1.698 1.469,1.698 false 1.552,2.052 1.469,2.052 false 0.708,2.781 1.031,2.781 false 3.156,7.594 3.448,7.76 0.292,0.167 10 false MB 4.875,6.385 5.167,6.552 0.292,0.167 10 false 2A 1.885,6.385 2.177,6.552 0.292,0.167 10 false 2B 1.167,5.115 1.458,5.281 0.292,0.167 10 false 2D 0.531,1.5 0.823,1.667 0.292,0.167 10 false 2D 3.927,5.135 4.219,5.302 0.292,0.167 10 false 2C 0.521,2.167 0.813,2.333 0.292,0.167 10 false 2C 4.875,3.802 5.167,3.969 0.292,0.167 10 false L7 6.26,5.104 6.552,5.271 0.292,0.167 10 false 2F 5.594,5.115 5.885,5.281 0.292,0.167 10 false 2E 5.875,5.115 6.083,5.281 0.208,0.167 10 false *B 6.552,5.115 6.76,5.281 0.208,0.167 10 false *C 2.438,3.813 2.729,3.979 0.292,0.167 10 false L8 0.271,2.563 0.563,2.729 0.292,0.167 10 false 2E 0.552,2.583 0.844,2.75 0.292,0.167 10 false *B 0.563,2.854 0.854,3.021 0.292,0.167 10 false *C 0.271,2.854 0.563,3.021 0.292,0.167 10 false 2F 2.01,1.698 2.302,1.865 0.292,0.167 10 false L7 2.01,2.063 2.302,2.229 0.292,0.167 10 false L8 6.271,1.542 6.479,1.708 0.208,0.167 10 false 2B 3.729,0.635 4.021,0.802 0.292,0.167 10 false MB 6.271,2.198 6.479,2.365 0.208,0.167 10 false 2A 1.823,0.583 1.979,0.74 0.156,0.156 10 false *1 0.375,0.198 0.635,0.396 0.26,0.198 10 false *A 1.365,3.313 1.521,3.469 0.156,0.156 10 false *2

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 3 connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) *2 3 connectors


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
L8-3 (GND2) - Body ground*1 W-B - Body ground Ground Always Below 1 Ω
MB-29 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-31 (ALTB) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch off Below 1 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the MB and L8*1 main body ECU (multiplex network body ECU) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
2D-35 (FLCY) - Body ground Y*2 - Body ground
V*3 - Body ground
Front door courtesy switch LH input Front door LH open Below 1 V
2D-35 (FLCY) - Body ground Y*2 - Body ground
V*3 - Body ground
Front door courtesy switch LH input Front door LH closed 11 to 14 V
2D-36 (FRCY) - Body ground BR*2 - Body ground
V*3 - Body ground
Front door courtesy switch RH input Front door RH open Below 1 V
2D-36 (FRCY) - Body ground BR*2 - Body ground
V*3 - Body ground
Front door courtesy switch RH input Front door RH closed 11 to 14 V

*1: Main Body ECU (Multiplex Network Body ECU) with 3 connectors

*2: for LHD

*3: for RHD


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.