When the hybrid control system is running or the power switch is on (IG), the power window regulator motor assembly (for driver door) is operated by the multiplex network master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.
The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
If the power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Communication D-Door Motor | Connection status between power window regulator motor (for driver door) and main body ECU (multiplex network body ECU) / STOP or OK | STOP: Communication stopped
OK: Normal communication |
- |
| Communication Master SW | Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU) / STOP or OK | STOP: Communication stopped
OK: Normal communication |
- |
On the GTS screen, OK is displayed.
OK
NG
(See pagePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Enter the following menus: Body Electrical / D-Door Motor / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| D Door P/W Up SW | Driver door power window manual up switch signal / OFF or ON | OFF: Driver door power window manual up switch not operated
ON: Driver door power window manual up switch operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal / OFF or ON | OFF: Driver door power window manual down switch not operated
ON: Driver door power window manual down switch operated |
- |
On the GTS screen, ON or OFF is displayed accordingly.
OK
NG
Enter the following menus: Body Electrical / D-Door Motor / Active Test.
Perform the Active Test according to the display on the GTS.
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF / UP / DOWN | - |
Driver door power window operates normally.
OK
NG
Disconnect the O6*1 or N13*2 multiplex network master switch assembly connector.
Disconnect the O2*1 or N2*2 power window regulator motor assembly (for driver door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O6-20 (UP) - O2-10 (UP) | Always | Below 1 Ω |
| O6-15 (DOWN) - O2-7 (DOWN) | Always | Below 1 Ω |
| O6-20 (UP) - Body ground | Always | 10 kΩ or higher |
| O6-15 (DOWN) - Body ground | Always | 10 kΩ or higher |
| O2-10 (UP) - Body ground | Always | 10 kΩ or higher |
| O2-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N13-20 (UP) - N2-10 (UP) | Always | Below 1 Ω |
| N13-15 (DOWN) - N2-7 (DOWN) | Always | Below 1 Ω |
| N13-20 (UP) - Body ground | Always | 10 kΩ or higher |
| N13-15 (DOWN) - Body ground | Always | 10 kΩ or higher |
| N2-10 (UP) - Body ground | Always | 10 kΩ or higher |
| N2-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).
NEXT
Check that the driver door power window moves when the manual up and down functions of the multiplex network master switch assembly are operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Driver door manual up and down functions are normal.
OK
NG