When the hybrid control system is running or the power switch is on (IG), the power window regulator motor assembly (for front passenger door) is operated by the power window regulator switch assembly. The power window regulator motor assembly (for front passenger door) has motor, regulator, and ECU functions.
The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
If the power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
After the catch protection function operates, the auto up function will not operate the first time power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Communication P-Door Motor | Connection status between power window regulator motor (for front passenger door) and main body ECU (multiplex network body ECU) / STOP or OK | STOP: Communication stopped
OK: Normal communication |
- |
On the GTS screen, OK is displayed.
OK
NG
(See pagePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Enter the following menus: Body Electrical / P-Door Motor / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P Door P/W Up SW | Front passenger door power window manual up switch signal / OFF or ON | OFF: Front passenger power window manual up switch not operated
ON: Front passenger door power window manual up switch operated |
- |
| P Door P/W Down SW | Front passenger door power window manual down switch signal / OFF or ON | OFF: Front passenger power window manual down switch not operated
ON: Front passenger door power window manual down switch operated |
- |
On the GTS screen, ON or OFF is displayed accordingly.
OK
NG
Enter the following menus: Body Electrical / P-Door Motor / Active Test.
Perform the Active Test according to the display on the GTS.
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF / UP / DOWN | - |
Front passenger door power window operates normally.
OK
NG
Remove the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (UP) - 1 (GND) | Auto up or up position | Below 1 Ω |
| 7 (DOWN) - 1 (GND) | Auto down or down position | Below 1 Ω |
| *a | Component without harness connected
(Power Window Regulator Switch Assembly) |
OK
NG
Disconnect the N2*1 or O2*2 power window regulator motor assembly (for front passenger door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N7-6 (UP) - N2-10 (UP) | Always | Below 1 Ω |
| N7-7 (DOWN) - N2-7 (DOWN) | Always | Below 1 Ω |
| N7-1 (GND) - Body ground | Always | Below 1 Ω |
| N7-6 (UP) - Body ground | Always | 10 kΩ or higher |
| N7-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| N2-10 (UP) - Body ground | Always | 10 kΩ or higher |
| N2-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O13-6 (UP) - O2-10 (UP) | Always | Below 1 Ω |
| O13-7 (DOWN) - O2-7 (DOWN) | Always | Below 1 Ω |
| O13-1 (GND) - Body ground | Always | Below 1 Ω |
| O13-6 (UP) - Body ground | Always | 10 kΩ or higher |
| O13-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| O2-10 (UP) - Body ground | Always | 10 kΩ or higher |
| O2-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
OK
NG