Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2012.03–2013.08
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301864 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, then fail-safe mode may be functioning.

If power window initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION) has not been performed, the auto up and down functions will not operate.

HINT:

If the pulse sensor built into the power window regulator motor assembly (for driver door) malfunctions, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the multiplex network master switch assembly at the auto up position, and opened manually by pushing down the multiplex network master switch assembly.


WIRING DIAGRAM

B234589E12
3.636,0.406 5.581,0.716 1.945,0.310 10 from Main Body ECU (Multiplex Network Body ECU) 1.078,2.31 2.734,2.473 1.656,0.162 10 : LIN Communication Line 3.18,1.96 3.919,2.122 0.739,0.162 10 *1: for LHD 3.18,2.31 3.919,2.473 0.739,0.162 10 *2: for RHD 0.299,1.64 1.120,1.781 0.821,0.141 10 O6*1, N13*2 0.3,1.792 2.976,1.933 2.676,0.141 10 Multiplex Network Master Switch Assembly 4.235,1.626 4.962,1.762 0.727,0.136 10 O2*1, N2*2 4.236,1.778 6.882,2.112 2.645,0.334 10 Power Window Regulator Motor Assembly (for Driver Door) 4.705,1.109 4.834,1.276 0.129,0.167 10 9 4.936,1.267 5.270,1.437 0.334,0.170 10 LIN 2.433,1.123 2.632,1.290 0.199,0.167 10 16 2.005,1.281 2.339,1.418 0.334,0.138 10 LIN2 2.433,0.297 2.632,0.463 0.199,0.167 10 17 2.005,0.454 2.339,0.592 0.334,0.138 10 LIN1

CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

·

If the power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



PROCEDURE

1.READ VALUE USING GTS (Master Switch)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Master switch / Data List.


e.

Read the Data List according to the display on the GTS.

Master Switch
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal / OFF or ON OFF: Driver door power window auto switch not operated
ON: Driver door power window auto switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

2.READ VALUE USING GTS (D-Door Motor)

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

2.READ VALUE USING GTS (D-Door Motor)
a.

Enter the following menus: Body Electrical / D-Door Motor / Data List.


b.

Read the Data List according to the display on the GTS.

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal / OFF or ON OFF: Driver door power window auto switch not operated
ON: Driver door power window auto switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

3.PERFORM INITIALIZATION (for Driver Door)

NG

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
3.PERFORM INITIALIZATION (for Driver Door)
a.

Initialize the power window regulator motor assembly (for driver door) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



NEXT

4.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
4.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
a.

Check that the driver door power window moves when the auto up and down functions of the multiplex network master switch assembly are operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).


OK:

Driver door auto up and down functions are normal.



OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Replace the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).



NEXT

6.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
6.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
a.

Check that the driver door power window moves when the auto up and down functions of the multiplex network master switch assembly are operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).


OK:

Driver door auto up and down functions are normal.



OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)