Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2013.08–2014.11
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301864 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the fail-safe mode may be functioning.

If power window initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION) has not been performed, the auto up and down functions will not operate.

HINT:

If the pulse sensor built into the power window regulator motor assembly (for front passenger door) malfunctions, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly.


WIRING DIAGRAM

B286849E05
0.953,0.474 4.208,0.614 3.255,0.140 10 from Main Body ECU (Multiplex Network Body ECU) 1.352,2.337 3.008,2.499 1.656,0.162 10 : LIN Communication Line 3.734,2.337 4.487,2.499 0.753,0.162 10 *2: for RHD 3.734,1.986 4.487,2.149 0.753,0.162 10 *1: for LHD 0.878,1.557 1.702,1.694 0.824,0.137 10 N7*1, O13*2 4.738,1.802 7.072,2.183 2.334,0.381 10 Power Window Regulator Motor Assembly (for Front Passenger Door) 0.879,1.709 3.572,1.854 2.693,0.145 10 Power Window Regulator Switch Assembly 4.738,1.638 5.477,1.776 0.739,0.138 10 N2*1, O2*2 4.962,0.299 5.090,0.465 0.129,0.167 10 9 2.699,1.099 2.828,1.266 0.128,0.167 10 8 1.039,1.098 1.167,1.265 0.129,0.167 10 1 5.193,0.456 5.527,0.626 0.334,0.170 10 LIN 4.962,1.102 5.090,1.269 0.129,0.167 10 4 5.193,1.212 5.693,1.382 0.501,0.170 10 AUTO 1.27,1.218 1.600,1.364 0.330,0.146 10 GND 2.188,1.214 2.596,1.355 0.407,0.141 10 AUTO

CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

·

If the power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



PROCEDURE

1.READ VALUE USING GTS (P-Door Motor)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / P-Door Motor / Data List.


e.

Read the Data List according to the display on the GTS.

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal / OFF or ON OFF: Front passenger door power window auto switch not operated
ON: Front passenger door power window auto switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

2.PERFORM INITIALIZATION (for Front Passenger Door)

NG

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
2.PERFORM INITIALIZATION (for Front Passenger Door)
a.

Initialize the power window regulator motor assembly (for front passenger door) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
a.

Check that the front passenger door power window moves when the auto up and down functions of the power window regulator switch assembly are operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Front passenger door auto up and down functions are normal.




OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
B203473E31
0.623,1.615 0.776,1.759 0.153,0.144 10 *a 0.059,2.635 0.468,2.774 0.410,0.139 10 AUTO 1.716,2.448 2.047,2.590 0.331,0.142 10 GND 0.806,2.719 0.55,2.719 false 1.699,2.524 1.413,2.524 false

Remove the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (AUTO) - 1 (GND) Auto up or auto down position Below 1 Ω


Text in Illustration
*a Component without harness connected
(Power Window Regulator Switch Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW SWITCH - REGULATOR MOTOR)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW SWITCH - REGULATOR MOTOR)
a.

Disconnect the N2*1 or O2*2 power window regulator motor assembly (for front passenger door) connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
N7-8 (AUTO) - N2-4 (AUTO) Always Below 1 Ω
N7-8 (AUTO) - Body ground Always 10 kΩ or higher
N2-4 (AUTO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
O13-8 (AUTO) - O2-4 (AUTO) Always Below 1 Ω
O13-8 (AUTO) - Body ground Always 10 kΩ or higher
O2-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR