Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2014.11
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301864 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the fail-safe mode may be functioning.

If power window initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION) has not been performed, the auto up and down functions will not operate.

HINT:

If the pulse sensor built into the power window regulator motor assembly (for rear LH door) malfunctions, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly (for LH door) at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly (for LH door).


WIRING DIAGRAM

B286849E02
0.967,0.467 4.215,0.607 3.248,0.140 10 from Main Body ECU (Multiplex Network Body ECU) 1.345,2.344 3.001,2.506 1.656,0.162 10 : LIN Communication Line 0.871,1.508 1.085,1.648 0.214,0.139 10 Q2 4.443,1.785 7.142,2.122 2.700,0.337 10 Power Window Regulator Motor Assembly (for Rear LH Door) 0.872,1.66 3.584,1.994 2.712,0.334 10 Rear Power Window Regulator Switch Assembly (for LH Door) 4.443,1.621 4.656,1.764 0.213,0.143 10 Q4 4.955,0.306 5.083,0.472 0.129,0.167 10 9 2.692,1.106 2.821,1.273 0.128,0.167 10 8 1.032,1.105 1.160,1.272 0.129,0.167 10 1 5.186,0.463 5.520,0.633 0.334,0.170 10 LIN 4.955,1.109 5.083,1.276 0.129,0.167 10 4 5.186,1.219 5.686,1.389 0.501,0.170 10 AUTO 1.263,1.225 1.593,1.367 0.330,0.142 10 GND 2.199,1.221 2.604,1.359 0.405,0.137 10 AUTO

CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

·

If the power window regulator motor assembly (for rear LH door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



PROCEDURE

1.READ VALUE USING GTS (RL-Door Motor)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / RL-Door Motor / Data List.


e.

Read the Data List according to the display on the GTS.

RL-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear LH door power window auto switch signal / OFF or ON OFF: Rear LH power window auto switch not operated
ON: Rear LH power window auto switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

2.PERFORM INITIALIZATION (for Rear LH Door)

NG

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
2.PERFORM INITIALIZATION (for Rear LH Door)
a.

Initialize the power window regulator motor assembly (for rear LH door) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
a.

Check that the rear LH door power window moves when the auto up and down functions of the rear power window regulator switch assembly (for LH door) are operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Rear LH door auto up and down functions are normal.




OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
a.
B203473E31
0.623,1.615 0.776,1.759 0.153,0.144 10 *a 0.059,2.635 0.468,2.774 0.410,0.139 10 AUTO 1.716,2.448 2.047,2.590 0.331,0.142 10 GND 0.806,2.719 0.55,2.719 false 1.699,2.524 1.413,2.524 false

Remove the rear power window regulator switch assembly (for LH door) (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (AUTO) - 1 (GND) Auto up or auto down position Below 1 Ω


Text in Illustration
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly (for LH Door))



OK

5.CHECK HARNESS AND CONNECTOR (REAR LH DOOR SWITCH - REAR LH DOOR MOTOR)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

5.CHECK HARNESS AND CONNECTOR (REAR LH DOOR SWITCH - REAR LH DOOR MOTOR)
a.

Disconnect the Q4 power window regulator motor assembly (for rear LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q2-8 (AUTO) - Q4-4 (AUTO) Always Below 1 Ω
Q2-8 (AUTO) - Body ground Always 10 kΩ or higher
Q4-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR