Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2012.03–2013.08
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301864 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies. The power window regulator motor assemblies have motor, regulator and ECU functions.

This DTC is output when the ECU built into a power window regulator motor assembly and multiplex network master switch assembly determine that the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly is stuck.

Master Switch
DTC No. DTC Detection Condition Trouble Area
B2312
·

Multiplex network master switch assembly stuck

·

Multiplex network master switch assembly held in same position for more than 20 seconds

·

Door control switch (multiplex network master switch assembly) operated for 20 seconds or more


Multiplex network master switch assembly

D-Door Motor
DTC No. DTC Detection Condition Trouble Area
B2312
·

Multiplex network master switch assembly stuck

·

Multiplex network master switch assembly held in same position for more than 20 seconds


·

Multiplex network master switch assembly

·

Power window regulator motor assembly (for driver door)

·

Wire harness or connector



P-Door Motor
DTC No. DTC Detection Condition Trouble Area
B2312
·

Power window regulator switch assembly stuck

·

Power window regulator switch assembly held in same position for more than 20 seconds


·

Power window regulator switch assembly

·

Power window regulator motor assembly (for front passenger door)

·

Wire harness or connector



RL-Door Motor
DTC No. DTC Detection Condition Trouble Area
B2312
·

Rear power window regulator switch assembly (for LH door) stuck

·

Power window regulator switch assembly held in same position for more than 20 seconds


·

Rear power window regulator switch assembly (for LH door)

·

Power window regulator motor assembly (for rear LH door)

·

Wire harness or connector



RR-Door Motor
DTC No. DTC Detection Condition Trouble Area
B2312
·

Rear power window regulator switch assembly (for RH door) stuck

·

Power window regulator switch assembly held in same position for more than 20 seconds


·

Rear power window regulator switch assembly (for RH door)

·

Power window regulator motor assembly (for rear RH door)

·

Wire harness or connector



WIRING DIAGRAM

for Driver Door


B234587E12
3.356,0.404 5.329,0.714 1.973,0.310 10 from Main Body ECU (Multiplex Network Body ECU) 0.287,2.742 1.874,3.049 1.587,0.307 10 Multiplex Network Master Switch Assembly 1.233,3.386 2.889,3.549 1.656,0.162 10 : LIN Communication Line 3.614,3.036 4.344,3.198 0.730,0.162 10 *1: for LHD 3.614,3.386 4.344,3.549 0.730,0.162 10 *2: for RHD 0.287,2.574 1.085,2.715 0.799,0.141 10 O6*1, N13*2 5.014,2.742 7.022,3.053 2.008,0.311 10 Power Window Regulator Motor Assembly (for Driver Door) 5.014,2.574 5.737,2.719 0.723,0.145 10 O2*1, N2*2 5.412,0.947 5.541,1.114 0.129,0.167 10 9 5.358,1.443 5.543,1.610 0.185,0.167 10 10 1.622,1.457 1.807,1.624 0.185,0.167 10 20 1.622,1.869 1.807,2.036 0.185,0.167 10 15 5.412,1.874 5.541,2.040 0.129,0.167 10 7 5.685,1.105 6.019,1.275 0.334,0.170 10 LIN 1.622,0.959 1.807,1.125 0.185,0.167 10 16 1.172,0.484 1.485,0.622 0.313,0.138 10 LIN1 1.622,0.328 1.807,0.495 0.185,0.167 10 17 1.172,1.108 1.485,1.247 0.313,0.138 10 LIN2 5.685,1.572 5.905,1.711 0.220,0.139 10 UP 5.685,1.983 6.153,2.123 0.468,0.141 10 DOWN 1.274,1.572 1.486,1.710 0.211,0.138 10 UP 1.024,1.983 1.483,2.121 0.459,0.138 10 DOWN


for Front Passenger Door


B286847E05
2.229,0.534 4.201,0.846 1.972,0.312 10 from Main Body ECU (Multiplex Network Body ECU) 1.259,4.328 2.915,4.490 1.656,0.162 10 : LIN Communication Line 0.229,3.461 1.027,3.602 0.798,0.140 10 N7*1, O13*2 5.252,3.629 6.937,4.161 1.685,0.532 10 Power Window Regulator Motor Assembly (for Front Passenger Door) 0.23,3.629 2.915,3.769 2.685,0.140 10 Power Window Regulator Switch Assembly 5.252,3.461 5.993,3.601 0.742,0.139 10 N2*1, O2*2 5.466,0.46 5.595,0.626 0.129,0.167 10 9 5.412,1.397 5.597,1.563 0.185,0.167 10 10 1.62,1.416 1.748,1.583 0.128,0.167 10 6 1.62,1.872 1.714,2.039 0.094,0.167 10 7 1.62,2.285 1.748,2.452 0.128,0.167 10 8 5.466,1.867 5.595,2.034 0.129,0.167 10 7 5.711,0.617 5.958,0.760 0.247,0.143 10 LIN 5.711,1.54 5.928,1.681 0.216,0.142 10 UP 5.711,1.99 6.174,2.137 0.463,0.146 10 DOWN 5.466,2.283 5.595,2.449 0.129,0.167 10 4 5.711,2.406 6.122,2.546 0.410,0.141 10 AUTO 1.303,1.548 1.514,1.687 0.211,0.140 10 UP 1.053,1.986 1.512,2.126 0.459,0.140 10 DOWN 1.11,2.4 1.513,2.542 0.403,0.142 10 AUTO 1.62,2.701 1.748,2.867 0.128,0.167 10 1 1.186,2.815 1.513,2.957 0.327,0.142 10 GND 3.688,3.977 4.418,4.140 0.730,0.162 10 *1: for LHD 3.688,4.328 4.418,4.490 0.730,0.162 10 *2: for RHD


for Rear LH Door


B286847E02
2.198,0.548 4.178,0.860 1.980,0.312 10 from Main Body ECU (Multiplex Network Body ECU) 1.246,4.328 2.902,4.490 1.656,0.162 10 : LIN Communication Line 0.236,3.345 0.452,3.497 0.216,0.153 10 Q2 5.109,3.552 7.119,3.959 2.010,0.407 10 Power Window Regulator Motor Assembly (for Rear LH Door) 0.237,3.497 2.277,3.831 2.040,0.334 10 Rear Power Window Regulator Switch Assembly (for LH Door) 5.109,3.389 5.337,3.550 0.228,0.161 10 Q4 5.473,0.463 5.602,0.630 0.129,0.167 10 9 5.419,1.414 5.604,1.581 0.185,0.167 10 10 1.635,1.424 1.763,1.590 0.128,0.167 10 6 1.635,1.88 1.746,2.066 0.112,0.187 10 7 1.635,2.292 1.763,2.459 0.128,0.167 10 8 5.473,1.87 5.602,2.037 0.129,0.167 10 7 5.716,0.627 5.957,0.764 0.240,0.137 10 LIN 5.716,1.549 5.931,1.688 0.215,0.139 10 UP 5.716,1.986 6.176,2.130 0.460,0.144 10 DOWN 5.473,2.286 5.602,2.453 0.129,0.167 10 4 5.716,2.401 6.120,2.543 0.404,0.141 10 AUTO 1.297,1.541 1.510,1.678 0.213,0.137 10 UP 1.049,1.993 1.508,2.130 0.459,0.136 10 DOWN 1.105,2.393 1.508,2.532 0.404,0.139 10 AUTO 1.635,2.707 1.763,2.874 0.128,0.167 10 1 1.178,2.822 1.509,2.967 0.331,0.144 10 GND


for Rear RH Door


B286847E03
2.236,0.553 4.198,0.865 1.963,0.312 10 from Main Body ECU (Multiplex Network Body ECU) 1.258,4.318 2.913,4.481 1.656,0.162 10 : LIN Communication Line 0.243,3.408 0.439,3.561 0.195,0.153 10 P2 5.266,3.616 6.871,4.092 1.604,0.476 10 Power Window Regulator Motor Assembly (for Rear RH Door) 0.245,3.56 2.297,3.894 2.053,0.334 10 Rear Power Window Regulator Switch Assembly (for RH Door) 5.266,3.452 5.457,3.613 0.191,0.161 10 P4 5.481,0.45 5.609,0.617 0.129,0.167 10 9 5.426,1.402 5.612,1.568 0.185,0.167 10 10 1.65,1.407 1.778,1.574 0.128,0.167 10 6 1.65,1.863 1.765,2.066 0.115,0.203 10 7 1.65,2.276 1.778,2.442 0.128,0.167 10 8 5.481,1.858 5.609,2.024 0.129,0.167 10 7 5.74,0.622 5.980,0.760 0.240,0.138 10 LIN 5.74,1.544 5.958,1.685 0.218,0.140 10 UP 5.74,1.995 6.207,2.133 0.467,0.138 10 DOWN 5.481,2.273 5.609,2.440 0.129,0.167 10 4 5.74,2.397 6.143,2.539 0.404,0.143 10 AUTO 1.285,1.535 1.503,1.672 0.218,0.138 10 UP 1.038,1.991 1.501,2.130 0.463,0.139 10 DOWN 1.095,2.405 1.501,2.543 0.406,0.138 10 AUTO 1.65,2.691 1.778,2.858 0.128,0.167 10 1 1.168,2.806 1.502,2.949 0.334,0.143 10 GND


CAUTION / NOTICE / HINT

HINT:

If DTC B2312 is not output again after the DTC has been cleared, the DTC was output due to the switch being held.


NOTICE:
·

DTC B2312 can be stored in the multiplex network master switch assembly and in each power window regulator motor assembly (power window ECU).

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC

OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

NG

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Check the parts which the DTCs have been output from.

Result:
Result Proceed to
DTC output from multiplex network master switch assembly A
DTC output from power window regulator motor assembly (for driver door) B
DTC output from power window regulator motor assembly (for front passenger door) C
DTC output from power window regulator motor assembly (for rear LH door) D
DTC output from power window regulator motor assembly (for rear RH door) E




A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

3.READ VALUE USING GTS (D-Door Motor)

C

7.READ VALUE USING GTS (P-Door Motor)

D

10.READ VALUE USING GTS (RL-Door Motor)

E

13.READ VALUE USING GTS (RR-Door Motor)
3.READ VALUE USING GTS (D-Door Motor)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / D-Door Motor / Data List.


e.

Read the Data List according to the display on the GTS.

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal / OFF or ON OFF: Driver door power window manual up switch not operated
ON: Driver door power window manual up switch operated
-
D Door P/W Down SW Driver door power window manual down switch signal / OFF or ON OFF: Driver door power window manual down switch not operated
ON: Driver door power window manual down switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

4.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER DOOR MOTOR)
4.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER DOOR MOTOR)
a.

Disconnect the O6*1 or N13*2 multiplex network master switch assembly connector.


b.

Disconnect the O2*1 or N2*2 power window regulator motor assembly (for driver door) connector.

·

*1: for LHD

·

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
O6-20 (UP) - Body ground Always 10 kΩ or higher
O6-15 (DOWN) - Body ground Always 10 kΩ or higher
O2-10 (UP) - Body ground Always 10 kΩ or higher
O2-7 (DOWN) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
N13-20 (UP) - Body ground Always 10 kΩ or higher
N13-15 (DOWN) - Body ground Always 10 kΩ or higher
N2-10 (UP) - Body ground Always 10 kΩ or higher
N2-7 (DOWN) - Body ground Always 10 kΩ or higher




OK

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Replace the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

7.READ VALUE USING GTS (P-Door Motor)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / P-Door Motor / Data List.


e.

Read the Data List according to the display on the GTS.

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal / OFF or ON OFF: Front passenger door power window auto switch not operated
ON: Front passenger door power window auto switch operated
-
P Door P/W Up SW Front passenger door power window manual up switch signal / OFF or ON OFF: Front passenger door power window manual up switch not operated
ON: Front passenger door power window manual up switch operated
-
P Door P/W Down SW Front passenger door power window manual down switch signal / OFF or ON OFF: Front passenger door power window manual down switch not operated
ON: Front passenger door power window manual down switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

8.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
8.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
B203473E29
0.623,1.607 0.776,1.750 0.153,0.144 10 *a 0.059,2.626 0.468,2.766 0.410,0.139 10 AUTO 1.716,2.439 2.047,2.581 0.331,0.142 10 GND 0.227,3.045 0.694,3.191 0.467,0.146 10 DOWN 1.445,3.045 1.658,3.186 0.213,0.141 10 UP 0.806,2.71 0.55,2.71 false 1.699,2.515 1.413,2.515 false 1.201,2.785 1.201,3.128 1.201,3.128 1.416,3.128 false 1.004,2.785 1.004,3.128 1.004,3.128 0.789,3.128 false

Remove the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (UP) - 1 (GND) Auto up or up position Below 1 Ω
7 (DOWN) - 1 (GND) Auto down or down position Below 1 Ω
8 (AUTO) - 1 (GND) Auto up or auto down position Below 1 Ω
6 (UP) - 1 (GND) Free 10 kΩ or higher
7 (DOWN) - 1 (GND) Free 10 kΩ or higher
8 (AUTO) - 1 (GND) Free 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Power Window Regulator Switch Assembly)



OK

9.CHECK HARNESS AND CONNECTOR (FRONT PASSENGER DOOR SWITCH - FRONT PASSENGER DOOR MOTOR)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (FRONT PASSENGER DOOR SWITCH - FRONT PASSENGER DOOR MOTOR)
a.

Disconnect the N7*1 or O13*2 power window regulator motor assembly (for front passenger door) connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
N7-6 (UP) - Body ground Always 10 kΩ or higher
N7-7 (DOWN) - Body ground Always 10 kΩ or higher
N7-8 (AUTO) - Body ground Always 10 kΩ or higher
N2-10 (UP) - Body ground Always 10 kΩ or higher
N2-7 (DOWN) - Body ground Always 10 kΩ or higher
N2-4 (AUTO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
O13-6 (UP) - Body ground Always 10 kΩ or higher
O13-7 (DOWN) - Body ground Always 10 kΩ or higher
O13-8 (AUTO) - Body ground Always 10 kΩ or higher
O2-10 (UP) - Body ground Always 10 kΩ or higher
O2-7 (DOWN) - Body ground Always 10 kΩ or higher
O2-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (RL-Door Motor)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / RL-Door Motor / Data List.


e.

Read the Data List according to the display on the GTS.

RL-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear LH door power window auto switch signal / OFF or ON OFF: Rear LH door power window auto switch not operated
ON: Rear LH door power window auto switch operated
-
RL Door P/W Up SW Rear LH door power window manual up switch signal / OFF or ON OFF: Rear LH door power window manual up switch not operated
ON: Rear LH door power window manual up switch operated
-
RL Door P/W Down SW Rear LH door power window manual down switch signal / OFF or ON OFF: Rear LH door power window manual down switch not operated
ON: Rear LH door power window manual down switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

11.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
11.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
a.
B203473E29
0.623,1.607 0.776,1.750 0.153,0.144 10 *a 0.059,2.626 0.468,2.766 0.410,0.139 10 AUTO 1.716,2.439 2.047,2.581 0.331,0.142 10 GND 0.227,3.045 0.694,3.191 0.467,0.146 10 DOWN 1.445,3.045 1.658,3.186 0.213,0.141 10 UP 0.806,2.71 0.55,2.71 false 1.699,2.515 1.413,2.515 false 1.201,2.785 1.201,3.128 1.201,3.128 1.416,3.128 false 1.004,2.785 1.004,3.128 1.004,3.128 0.789,3.128 false

Remove the rear power window regulator switch assembly (for LH door) (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (UP) - 1 (GND) Auto up or up position Below 1 Ω
7 (DOWN) - 1 (GND) Auto down or down position Below 1 Ω
8 (AUTO) - 1 (GND) Auto up or auto down position Below 1 Ω
6 (UP) - 1 (GND) Free 10 kΩ or higher
7 (DOWN) - 1 (GND) Free 10 kΩ or higher
8 (AUTO) - 1 (GND) Free 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly (for LH Door))



OK

12.CHECK HARNESS AND CONNECTOR (REAR LH SWITCH - REAR LH MOTOR)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

12.CHECK HARNESS AND CONNECTOR (REAR LH SWITCH - REAR LH MOTOR)
a.

Disconnect the Q4 power window regulator motor assembly (for rear LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q2-6 (UP) - Body ground Always 10 kΩ or higher
Q2-7 (DOWN) - Body ground Always 10 kΩ or higher
Q2-8 (AUTO) - Body ground Always 10 kΩ or higher
Q4-10 (UP) - Body ground Always 10 kΩ or higher
Q4-7 (DOWN) - Body ground Always 10 kΩ or higher
Q4-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.READ VALUE USING GTS (RR-Door Motor)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / RR-Door Motor / Data List.


e.

Read the Data List according to the display on the GTS.

RR-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear RH door power window auto switch signal / OFF or ON OFF: Rear RH door power window auto switch not operated
ON: Rear RH door power window auto switch operated
-
RR Door P/W Up SW Rear RH door power window manual up switch signal / OFF or ON OFF: Rear RH door power window manual up switch not operated
ON: Rear RH door power window manual up switch operated
-
RR Door P/W Down SW Rear RH door power window manual down switch signal / OFF or ON OFF: Rear RH door power window manual down switch not operated
ON: Rear RH door power window manual down switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

NG

14.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
14.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
a.
B203473E29
0.623,1.607 0.776,1.750 0.153,0.144 10 *a 0.059,2.626 0.468,2.766 0.410,0.139 10 AUTO 1.716,2.439 2.047,2.581 0.331,0.142 10 GND 0.227,3.045 0.694,3.191 0.467,0.146 10 DOWN 1.445,3.045 1.658,3.186 0.213,0.141 10 UP 0.806,2.71 0.55,2.71 false 1.699,2.515 1.413,2.515 false 1.201,2.785 1.201,3.128 1.201,3.128 1.416,3.128 false 1.004,2.785 1.004,3.128 1.004,3.128 0.789,3.128 false

Remove the rear power window regulator switch assembly (for RH door) (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (UP) - 1 (GND) Auto up or up position Below 1 Ω
7 (DOWN) - 1 (GND) Auto down or down position Below 1 Ω
8 (AUTO) - 1 (GND) Auto up or auto down position Below 1 Ω
6 (UP) - 1 (GND) Free 10 kΩ or higher
7 (DOWN) - 1 (GND) Free 10 kΩ or higher
8 (AUTO) - 1 (GND) Free 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly (for RH Door))



OK

15.CHECK HARNESS AND CONNECTOR (REAR RH SWITCH - REAR RH MOTOR)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

15.CHECK HARNESS AND CONNECTOR (REAR RH SWITCH - REAR RH MOTOR)
a.

Disconnect the P4 power window regulator motor assembly (for rear RH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P2-6 (UP) - Body ground Always 10 kΩ or higher
P2-7 (DOWN) - Body ground Always 10 kΩ or higher
P2-8 (AUTO) - Body ground Always 10 kΩ or higher
P4-10 (UP) - Body ground Always 10 kΩ or higher
P4-7 (DOWN) - Body ground Always 10 kΩ or higher
P4-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR