Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2012.03–2013.08
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301864 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2311  Power Window Motor Malfunction  


DESCRIPTION

The power window regulator motor assembly is operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly. The power window regulator motor assembly has motor, regulator and ECU functions.

This DTC is output when the power window regulator motor assembly has a malfunction, or the ECU built into the power window regulator motor assembly determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

D-Door Motor
DTC No. DTC Detection Condition Trouble Area
B2311

Either condition is met:

(a)

Power window regulator motor assembly malfunctions

(b)

When ECU in power window regulator motor assembly determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position



·

Power window regulator motor assembly (for driver door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly



P-Door Motor
DTC No. DTC Detection Condition Trouble Area
B2311

Either condition is met:

(a)

Power window regulator motor assembly malfunctions

(b)

When ECU in power window regulator motor assembly determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position



·

Power window regulator motor assembly (for front passenger door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly



RL-Door Motor
DTC No. DTC Detection Condition Trouble Area
B2311

Either condition is met:

(a)

Power window regulator motor assembly malfunctions

(b)

When ECU in power window regulator motor assembly determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position



·

Power window regulator motor assembly (for rear LH door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly



RR-Door Motor
DTC No. DTC Detection Condition Trouble Area
B2311

Either condition is met:

(a)

Power window regulator motor assembly malfunctions

(b)

When ECU in power window regulator motor assembly determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position



·

Power window regulator motor assembly (for rear RH door)

·

Incorrect installation of power window components

·

Overheated power window regulator motor assembly



CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2311 can be stored in each power window regulator motor assembly (power window ECU).

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / (desired system) / Active Test.

HINT:

Perform the Active Test for the power window regulator motor assembly that has DTC B2311 stored in its ECU.



e.

Perform the Active Test according to the display on the GTS.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


D-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -

P-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -

RL-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -

RR-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -

OK:

Each power window motor operates.


Result:
Result Proceed to
OK A
NG (Driver door power window) B
NG (Front passenger door power window) B
NG (Rear LH door power window) C
NG (Rear RH door power window) C




A

2.PERFORM INITIALIZATION (APPLICABLE LOCATION)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door or Front Passenger Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door or Rear RH Door)

2.PERFORM INITIALIZATION (APPLICABLE LOCATION)
a.

Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

HINT:

Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.




NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION)
3.CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION)
a.

Check that the power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

HINT:

Check the power window operation of the window where DTC B2311 has been stored.


OK:

Each power window operates normally.


Result:
Result Proceed to
OK A
NG (Driver door power window) B
NG (Front passenger door power window) B
NG (Rear LH door power window) C
NG (Rear RH door power window) C




A

4.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door or Front Passenger Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door or Rear RH Door)

4.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
a.

Check that the power window components are installed correctly.

OK:

Power window components are installed correctly.




OK

5.CHECK DTC OUTPUT

NG

INSTALL PARTS CORRECTLY

5.CHECK DTC OUTPUT
a.

Turn the power switch off.


b.

Wait for at least 10 seconds, and then turn the power switch to ON.


c.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

OK:

B2311 output does not recur.


Result:
Result Proceed to
OK A
NG (Driver door power window) B
NG (Front passenger door power window) B
NG (Rear LH door power window) C
NG (Rear RH door power window) C




A

END

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door or Front Passenger Door)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door or Rear RH Door)